[Home] [This version is outdated, a new version is here]
*Title...
*Search:...
*Read Me/FAQ/General Info...
*_IBM...
*ACC Micro...
*ALD...
*ALi...
*AMD . . . . . . . [no datasheets, some info]...
*Chips & Technologies...
*Contaq  . . . . . [no datasheets, some info]...
*Efar Microsystems [no datasheets, some info]...
*ETEQ...
*Faraday...
*Forex . . . . . . [List only, no datasheets found]...
*Intel...
**82395SX     Smart Cache                                     12/17/90
***Notes:...
**82396SX     Smart Cache                                     12/17/90...
**82485       Turbo Cache (and 485Turbocache)                      c90...
**82489DX       Advanced Programmable Interrupt Controller    10/12/92...
**82495DX/490DX DX CPU-Cache Chip Set                           <Sep91...
**82495XP/490XP Cache Controller / Cache RAM (for i860)       06/05/91...
**82496/491     Cache Controller / Cache RAM (for P5 Pentium) 03/22/93...
**82497/492   Cache Controller / Cache RAM (for P54 Pentium)    <Nov94...
**82498/493   Cache Controller / Cache RAM (for P54 Pentium)    <Nov94...
**
**Later chipsets (basic spec):
**440 series:...
**450NX  (?)            06/29/98:...
**?????  (Profusion)    c:99...
**800 series...
*Headland/G2...
**HT44          Secondary Cache                                c:Jun92
***Info:
The  HT44 is  a  look-aside write-through,  80486SX,  486DX or  486DX2
secondary cache  controller. It is  packaged in an  inexpensive 84-pin
plastic-leaded chip carrier (PLCC).

Architecture
With  its look-aside architecture,  the HT44  fits beside  the CPU-to-
Memory bus  and not in  the data path.   Therefore, once the  HT44 has
been designed  into a  486 system, it  can be populated  for secondary
cache systems or left vacant for non-secondary cache systems. The HT44
is direct-mapped to the available address space.

Performance
The  HT44  has a  number  of  performance  enhancing features.   These
include zero-waitstate burst line fills  to the 486 on secondary cache
hits, and simultaneous 486 and secondary cache updates on read misses.

Memory Configurations
The HT44 supports  cache sizes from 32KBytes to  1MB. Both synchronous
and asynchronous  SRAMs are supported.  25ns SRAMs are  sufficient for
zero-wait-state operation at 33MHz.

Chip Set Support
The HT44 can,  be implemented with minimal glue logic  in a 486 system
with the  HTK340 (code  name Shasta) chip  set.  The registers  in the
HTK340  allow  for programming  of  non-cacheable and  write-protected
areas of  memory. The  HTK340 will support  the HT44  with synchronous
SRAMs only.   Future Headland chip sets will  support both synchronous
and asynchronous SRAM designs.

The HT44  can also be used  with some third-party  chip sets, however,
additional glue logic may be required.

***Versions:...
***Features:...
**Other:...
*HMC (Hulon Microelectronics)...
*Logicstar...
*Motorola...
*OPTi...
*PC CHIPS/Amptron/Atrend/ECS/Elpina/etc...
*SIS...
*Symphony...
*TI (Texas Instruments)...
*UMC...
*Unresearched:...
*VIA...
*VLSI...
*Western Digital...
*Winbond...
**W83769          Local Bus IDE Solution                           <94
***Info:
GENERAL DESCRIPTION

The W83769  is a  high-performance, low-cost, highly  integrated logic
design  for IDE hard  disk applications  in PCI  (Peripheral Component
Interconnect)  local  bus systems.  It  provides  a  bridge between  a
standard  IDE  drive  and the  PCI  local  bus.  The W83769  is  fully
compatible  with the  ANSI ATA  3.0 specifications  for IDE  hard disk
operation  and the  PCI SIG  revision 2.0  specifications for  the PCI
local bus  protocol. Packaged in  a 100-pin PQFP, the  W83769 directly
supports the 32-bit PCI bus without requiring any external TTLs.

The W83769  operates at up to 50  MHz and provides a  full 32-bit data
path to the PCI bus. Doubleword read and write operations are provided
via  internal   control  and  conversion  logic.   Write  posting  and
read-ahead  allows CPU  memory  cycles to  run  concurrently with  IDE
cycles and improves the hard disk buffer-to-host transfer rate.

The IDE  drive interface timing  of the W83769 is  completely software
programmable,  including command  active/recovery  timing and  address
setup-hold   timing  for   each  drive.   The  device   supports  Fast
ATA/Enhanced  IDE  mode  3  timing  and IORDY  monitoring  for  better
performance.   The  W83769  directly  supports four  IDE  drives  with
170/1F0   dual   IDE  connectors.   The  IO base   addresses  of   the
primary/secondary  IDE connector  are exchangeable  by  power-on strap
option.

***Versions:...
***Features:...
**
**UARTS:
**W86C250A  UART (equivalent of INS8C250A) [no datasheet]
**W86C450/P Universal Asynchronous Receiver/Transmitter         <Jul89...
**W86C451   I/O controller for IBM PC/AT/XT                     <Jul89...
**W86C452   I/O controller for IBM PC/AT                         Jul89...
**W86C456   I/O controller [no datasheet]                            ?
**W860551/P UART with FIFO and Printer Port Controller             <94...
**
**Other:...
*ZyMOS...
*General Sources:...