[Home] [This version is outdated, a new version is here]
*Title...
*Search:...
*Read Me/FAQ/General Info...
*_IBM...
*ACC Micro...
*ALD...
*ALi...
*AMD . . . . . . . [no datasheets, some info]...
*Chips & Technologies...
*Contaq . . . . . [no datasheets, some info]...
*Efar Microsystems [no datasheets, some info]...
*ETEQ...
*Faraday...
*Forex . . . . . . [List only, no datasheets found]...
*Intel...
**82495XP/490XP Cache Controller / Cache RAM (for i860) 06/05/91
***Notes:...
***Info:...
***Features:...
**82496/491 Cache Controller / Cache RAM (for P5 Pentium) 03/22/93...
**82497/492 Cache Controller / Cache RAM (for P54 Pentium) <Nov94...
**82498/493 Cache Controller / Cache RAM (for P54 Pentium) <Nov94...
**
**Later chipsets (basic spec):
**440 series:...
**450NX (?) 06/29/98:...
**????? (Profusion) c:99...
**800 series...
*Headland/G2...
*HMC (Hulon Microelectronics)...
*Logicstar...
*Motorola...
*OPTi...
**82C895 System/Power Management Controller (cached) c:Sep94
***Notes:...
***Info:...
***Configurations:...
***Features:
o Processor interface:
- Intel 80486SX, DX, DX2, SLe, DX4, P24T, P24D
- AMD 486DX, DX2, DXL, DXL2, Plus
- Cyrix DX, DX2, M7
- CPU frequencies supported 20, 25, 33, 40 and 50MHz
o Cache interface:
- Direct Mapped Cache
- Two banks interleaved or single bank non-interleaved
- 64, 128, 256 and 512K cache sizes
- Programmable wait states for L2 cache reads and writes
- 2-1-1-1 read burst and zero wait state write @ 33MHz
- No Valid bit required
- Supports CPUs with L1 write-back support
o DRAM interface:
- Up to 128MB main memory support
- Supports 256KB, 1MB, 4MB, and 16MB single- and double-sided SIMM
modules
- Read page-hit timing of 3-2-2-2 at 33MHz
- Supports hidden, slow and CAS-before-RAS refresh
- Four RAS lines to support four banks of DRAM
- Programmable wait states for DRAM reads and writes
- Enhanced DRAM configuration map
o Power management:
- Support for SMM (System Management Mode) for system power
management implementations
- Programmable power management
- Programmable wake-up events through hardware, software and
external SMI source
- Multiple level GREEN support (NESTED_GREEN)
- STPCLK# protocol support
- One programmable GREEN event timer
o ISA interface:
- 100% IBM PC/AT ISA compatible
- Integrates DMA, timer and interrupt controllers
- Optional PS/2 style IRQ1 and 12 latching
o VESA VL interface:
- Conforms to the VESA v2.0 specification
- Optional support for up to two VL masters
o Miscellaneous features:
- Full support for shadow RAM, write protection, L1/L2
cacheability for video, adapter and system BIOS
- Enhanced arbitration scheme
- Transparent 8042 emulation for fast CPU reset and GATEA20
generation
o Packaging:
- Higher integration
- Reduced TTL count
- Low-power, high-speed 0.8-micron CMOS technology
- 208-pin PQFP (Plastic Quad Flat Pack)
**82C898 System/Power Management Controller (non-cache)c:Nov94...
**
**Support Chips:
**82C601/2 Buffer Devices <Nov94...
**82C822 PCIB (VLB-to-PCI bridge) c:94...
**Other:...
*PC CHIPS/Amptron/Atrend/ECS/Elpina/etc...
*SIS...
*Symphony...
*TI (Texas Instruments)...
*UMC...
*Unresearched:...
*VIA...
*VLSI...
*Western Digital...
**WD76C30x Perip. Ctrl, Interrupt Multiplex, and Clock Gen <11/18/91
***Notes:...
***Info:
GENERAL
The WD76C30/LV device provides three functional groups. It is a Per-
ipheral Controller, Interrupt Multiplexer, and Clock Generator.
The low power CMOS WD76C30/LV is a single device solution which
provides interrupt multiplexing logic, clock generation, two serial
ports, and one bidirectional parallel port.
Interrupt multiplexing logic interfaces the PC/AT interrupt request
lines with the WD76C10 Single Chip AT Controller.
Integrated clock generation circuitry uses the 48 MHz input signal to
generate the 1.8462, 3.072, and 8.0 MHz clocks used internally for the
two serial ports, a 9.6 MHz Signal used for the keyboard controller
and floppy controller, a programmable duty/frequency clock for the
80287 coprocessor, and a 16 MHz clock for driving the WD76C10 Single
Chip AT Controller, and floppy controller.
For low power implementations such as laptops, oscillator disable and
sleep modes are available to power down unused logic.
The bidirectional parallel port is software configurable as either a
PC/AT or a PS/2 compatible port. The parallel port data lines and open
drain printer signals have high current drive capabilities.
Each ACE is programmable as either a WD16C550 or WD16C450 compatible
device. Each WD16C550 configured ACE is capable of buffering up to 16
bytes of data upon reception, relieving the CPU of interrupt
overhead. Buffering of data also allows greater latency time in
interrupt servicing which is vital in a multitasking environment. Each
ACE has a maximum recommended data rate of 512 Kbaud.
WD76C30/LV DIFFERENCES
Both the WD76C30 and WD76C30LV operate with two power supplies. The
WD76C30 logic is powered by a 5.0 volt supply, while the WD76C30LV
logic is powered by a 3.3 volt supply. The parallel and serial port
interfaces are only supported by the WD76C30.
PERIPHERAL CONTROLLER
The peripheral controller is functionally equivalent to the WD16C452/
552. The mode of operation of the serial ports and parallel port is
selectable via the Mode Select Register. Each serial port is
configurable as either a FIFO enhanced ACE (WD16C550 compatible) or a
standard ACE (WD16C450). The parallel port is configurable as either a
PS/2 bidirectional parallel port or a PC/AT compatible parallel port.
A detailed description of the Mode Selection Register is described in
the parallel port section.
***Versions:...
***Features:...
**WD7615 Desktop Buffer Manager <04/15/92...
**WD7625 Desktop Buffer Manager <10/01/92...
**WD8120LV Super I/O [no datasheet] ?
**Other Chips:...
*Winbond...
*ZyMOS...
*General Sources:...
(c) Copyright mR_Slugs Warehouse - All rights Reserved