[Home] [This version is outdated, a new version is here]
*Title...
*Search:...
*Read Me/FAQ/General Info...
*_IBM...
*ACC Micro...
*ALD...
*ALi...
*AMD . . . . . . . [no datasheets, some info]...
*Chips & Technologies...
*Contaq  . . . . . [no datasheets, some info]...
*Efar Microsystems [no datasheets, some info]...
*ETEQ...
*Faraday...
*Forex . . . . . . [List only, no datasheets found]...
*Intel...
**?????  (Profusion)    c:99
Chips:         
Memory Access Controller (MAC)  
Data Interface Buffer (DIB)
CPUs:          8x P-III Xeon Oct
DRAM Types:    SDRAM PC100 2-way Interleave dual channel
Max Mem:       32GB
ECC/Parity:    ECC
AGP speed:     N/A
Bus Speed:     100
PCI Clock/Bus: 1/3 PCI-66/64



**800 series...
*Headland/G2...
**HT22          386SX/286 Single Chip (25 MHz)                 c:Sep91
***Info:
The HT22  is an  advanced PC/AT compatible,  single-chip 80386SX/80286
system  design solution.   This highly  integrated single  chip allows
simple, low  cost system design  options while featuring  high perfor-
mance,  low  power  consumption,  and  minimum  board  space  require-
ments. Advanced  memory management  features include support  for page
mode,  2 or  4-way interleaving  in both  pipelined  and non-pipelined
modes.  The EMS  4.0 hardware implementation features dual  sets of 32
registers   with  full   context  support   for   highest  performance
optimization  of  extended local  memory  accesses.   An advanced  EMS
hardware  write-protect option  has  been added  for  maximum EMS  4.0
compatibility. The HTZ2 supports 256K, 1M  and 4MB DRAMs in 1 by 1 and
1 by 4 device configurations for up to 20MB of on-board system memory.
16MB  is  addressed  directly   by  system  resources,  the  remainder
addressed by the EMS mode.

A flexible Shadow  RAM option for System and Video BIOS  as well as 8-
16-bit BIOS options adds to overall design versatility.

A  complete PC/AT  compatible  system with  advanced  features may  be
implemented with minimal external support logic. The HT22 performs all
CPU  and peripheral support  functions in  a single  chip.  Integrated
device  functions include  DMA Controllers,  a Memory  Mapper, Timers,
Counters, Interrupt  Controllers, a Bus Controller  and all supporting
circuitry for PC  core logic requirements. The chip  also contains all
the  necessary  address buffers,  data  transceivers, memory  drivers,
parity  checking   and  supporting  circuitry  for   a  complete  high
performance computer  solution.  An  asynchronous AT Bus  clock allows
for  a constant 8MHz  Bus clock  rate for  highest bus  device compat-
ibility as  defined in IEEE  Spec P996. This  device is packaged  in a
208-pin Plastic Quad Flat Pack.

***Configurations:...
***Features:...
**HT25          3-volt Core Logic for 386SX                    c:Dec92...
**HT35          Single-Chip Peripheral Controller [partial info]     ?...
**HTK320        386DX Chip Set                                 c:Sep91...
**HTK340        "Shasta" 486 Chip Set                          c:Jun92...
**Support Chips:
**HT44          Secondary Cache                                c:Jun92
***Info:
The  HT44 is  a  look-aside write-through,  80486SX,  486DX or  486DX2
secondary cache  controller. It is  packaged in an  inexpensive 84-pin
plastic-leaded chip carrier (PLCC).

Architecture
With  its look-aside architecture,  the HT44  fits beside  the CPU-to-
Memory bus  and not in  the data path.   Therefore, once the  HT44 has
been designed  into a  486 system, it  can be populated  for secondary
cache systems or left vacant for non-secondary cache systems. The HT44
is direct-mapped to the available address space.

Performance
The  HT44  has a  number  of  performance  enhancing features.   These
include zero-waitstate burst line fills  to the 486 on secondary cache
hits, and simultaneous 486 and secondary cache updates on read misses.

Memory Configurations
The HT44 supports  cache sizes from 32KBytes to  1MB. Both synchronous
and asynchronous  SRAMs are supported.  25ns SRAMs are  sufficient for
zero-wait-state operation at 33MHz.

Chip Set Support
The HT44 can,  be implemented with minimal glue logic  in a 486 system
with the  HTK340 (code  name Shasta) chip  set.  The registers  in the
HTK340  allow  for programming  of  non-cacheable and  write-protected
areas of  memory. The  HTK340 will support  the HT44  with synchronous
SRAMs only.   Future Headland chip sets will  support both synchronous
and asynchronous SRAM designs.

The HT44  can also be used  with some third-party  chip sets, however,
additional glue logic may be required.

***Versions:...
***Features:...
**Other:...
*HMC (Hulon Microelectronics)...
*Logicstar...
*Motorola...
*OPTi...
*PC CHIPS/Amptron/Atrend/ECS/Elpina/etc...
*SIS...
*Symphony...
*TI (Texas Instruments)...
*UMC...
*Unresearched:...
*VIA...
*VLSI...
*Western Digital...
*Winbond...
*ZyMOS...
*General Sources:...