[Home] [This version is outdated, a new version is here]
*Title...
*Search:...
*Read Me/FAQ/General Info...
*_IBM...
*ACC Micro...
*ALD...
*ALi...
*AMD . . . . . . . [no datasheets, some info]...
*Chips & Technologies...
*Contaq  . . . . . [no datasheets, some info]...
*Efar Microsystems [no datasheets, some info]...
*ETEQ...
*Faraday...
*Forex . . . . . . [List only, no datasheets found]...
*Intel...
**450NX  (?)            06/29/98:
Chips:
[82454NX] (PXB) [82453NX] (MUX) 
[82452NX] (RCG) [82451NX] (MIOC) 
[82371EB] (PIIX4E),                            
CPUs:          Single/Dual/Quad P-II Xeon/P-III Xeon
DRAM Types:    FPM EDO 2-way Interleave 4-way Interleave
Mem Rows:      8
DRAM Density:  16Mbit 64Mbit
Max Mem:       8GB
ECC/Parity:    Both
AGP speed:     N/A
Bus Speed:     100
PCI Clock/Bus: 1/3


**?????  (Profusion)    c:99...
**800 series...
*Headland/G2...
**HT44          Secondary Cache                                c:Jun92
***Info:
The  HT44 is  a  look-aside write-through,  80486SX,  486DX or  486DX2
secondary cache  controller. It is  packaged in an  inexpensive 84-pin
plastic-leaded chip carrier (PLCC).

Architecture
With  its look-aside architecture,  the HT44  fits beside  the CPU-to-
Memory bus  and not in  the data path.   Therefore, once the  HT44 has
been designed  into a  486 system, it  can be populated  for secondary
cache systems or left vacant for non-secondary cache systems. The HT44
is direct-mapped to the available address space.

Performance
The  HT44  has a  number  of  performance  enhancing features.   These
include zero-waitstate burst line fills  to the 486 on secondary cache
hits, and simultaneous 486 and secondary cache updates on read misses.

Memory Configurations
The HT44 supports  cache sizes from 32KBytes to  1MB. Both synchronous
and asynchronous  SRAMs are supported.  25ns SRAMs are  sufficient for
zero-wait-state operation at 33MHz.

Chip Set Support
The HT44 can,  be implemented with minimal glue logic  in a 486 system
with the  HTK340 (code  name Shasta) chip  set.  The registers  in the
HTK340  allow  for programming  of  non-cacheable and  write-protected
areas of  memory. The  HTK340 will support  the HT44  with synchronous
SRAMs only.   Future Headland chip sets will  support both synchronous
and asynchronous SRAM designs.

The HT44  can also be used  with some third-party  chip sets, however,
additional glue logic may be required.

***Versions:...
***Features:...
**Other:...
*HMC (Hulon Microelectronics)...
*Logicstar...
*Motorola...
*OPTi...
*PC CHIPS/Amptron/Atrend/ECS/Elpina/etc...
*SIS...
*Symphony...
*TI (Texas Instruments)...
*UMC...
*Unresearched:...
*VIA...
*VLSI...
**VL82C3216        Bus Expanding Controller Cache with write buffer  ?
***Info:...
***Versions:...
***Features:...
**VL82C521/522     Lynx/M                                            ?...
**VL82C530         Eagle Ð                                         c95...
**VL82C541/543     Lynx                                            c95...
**VL82C591/593     SuperCore 590                                   c94...
**VL82C594/596/597 Wildcat                                         c95...
**I/O Chips:
**VL82C106 Combination I/O chip                                      ?...
**VL82C107 SCAMP  Combination I/O chip                               ?...
**VL82C108 TOPCAT Combination I/O chip                               ?...
**VL82C110 Combination I/O chip                                      ?...
**VL82C113 SCAMP  Combination I/O chip                               ?...
**VL82C114 Combination I/O chip                                      ?...
**Video: ...
**Disk:...
**Modems:...
**Other:...
**Not sure if they actually exist...
*Western Digital...
*Winbond...
*ZyMOS...
*General Sources:...