; zds video card ; BOARD ID = "ZDSF028" NAME = "Z-649 Video" MFR = "VID" CATEGORY = "VID" SLOT = ISA16 LENGTH = 220 ; HEIGHT = 100 SKIRT = NO READID = no AMPERAGE = 2000 DISABLE = UNSUPPORTED IOCHECK = INVALID COMMENTS = "This is the ZDS Z-649 (152-36-W1) ISA video Controller. The board itself is a standard ISA device. The EISA file for this board will clear the TIGA video on reboot. (version 1.02)" HELP="This is an I/O mapped video processor board, based on the TIGA (TM) software interface. A VGA card pass through or a VGA daughter card should be used in conjunction with this card. This file works for part (152-36-W1). TIGA is a trademark of Texas Instruments Inc. (version 1.02)" JUMPER(1) = 6 NAME = "Host Interrupt" JTYPE = PAIRED VERTICAL = YES REVERSE = YES LABEL = LOC(1-6) "IRQ5" "IRQ7" "IRQ10" "IRQ11" "IRQ12" "IRQ15" FACTORY = LOC(1-6) 001000 COMMENTS = "This set of video board jumpers selects which Host Interrupt Request (IRQ) this board should utilize. Only one jumper should be installed at any one time." JUMPER(2) = 1 NAME = "Host Port Address" JTYPE = TRIPOLE VERTICAL = YES REVERSE = YES LABEL = LOC(1) "W1" FACTORY = LOC(1) 0 COMMENTS = "This Jumper is used to determine the Host ports used to access this board. A connection between the first jumpers indicates ports 290 - 29F, a connection between the second jumpers indicates ports 280-28F." FUNCTION = "Host IRQ" TYPE = "VID" HELP = "This function determines which Host Interrupt Request this board should use. Changes made under this function may affect the Host Interrupt jumper block. See Jumper/Switch settings if the configuration of this function is changed." CHOICE = "IRQ 10" FREE INIT = Jumper(1) LOC(1-6) 001000 IRQ = 10 SHARE = NO TRIGGER = EDGE CHOICE = "IRQ 5" FREE INIT = Jumper(1) LOC(1-6) 100000 IRQ = 5 SHARE = NO TRIGGER = EDGE CHOICE = "IRQ 7" FREE INIT = Jumper(1) LOC(1-6) 010000 IRQ = 7 SHARE = NO TRIGGER = EDGE CHOICE = "IRQ 11" FREE INIT = Jumper(1) LOC(1-6) 000100 IRQ = 11 SHARE = NO TRIGGER = EDGE CHOICE = "IRQ 12" FREE INIT = Jumper(1) LOC(1-6) 000010 IRQ = 12 SHARE = NO TRIGGER = EDGE CHOICE = "IRQ 15" FREE INIT = Jumper(1) LOC(1-6) 000001 IRQ = 15 SHARE = NO TRIGGER = EDGE FUNCTION = "Host Ports" TYPE = "VID" HELP = "This function determines which Ports the Host should use to access this board. Changes made under this function may affect the Host Port Address jumper block. See Jumper/Switch settings if the configuration of this function is changed." CHOICE = "Ports 290-29F" FREE PORT = 0290h - 029fh ;Host ports SHARE = No Size = Byte INIT = PORTADR(290h) WORD 0010000000000000 INIT = PORTADR(292h) WORD 0000000000000000 INIT = PORTADR(294h) WORD 0000000000000000 INIT = Jumper(2) LOC(1) 0 CHOICE = "Ports 280-28F" FREE PORT = 0280h - 028fh ;Host ports SHARE = No Size = Byte INIT = PORTADR(280h) WORD 0010000000000000 INIT = PORTADR(282h) WORD 0000000000000000 INIT = PORTADR(284h) WORD 0000000000000000 INIT = Jumper(2) LOC(1) 1 FUNCTION = "VIDEO Daughter Card" TYPE = "VID" HELP = "This card can be configured with an optional video daughter card. The daughter card acts as a standard VGA interface board. This removes the need for a VGA board to be present in another board slot. This is a hardware option, and cannot be changed without removing this board and adding or removing the daughter card from it." CHOICE = "Not Installed" CHOICE = "Installed" FREE PORT = 03B7h - 03Dfh ;Video ports PORT = 0102h ;VGA setup port PORT = 46E8h ;VGA enable port MEMORY = 64K ;Video Memory ADDRESS = 0A0000h WRITABLE = NO MEMTYPE = SYS SIZE = BYTE SHARE = No MEMORY = 64K ;Video Memory ADDRESS = 0B0000h WRITABLE = NO MEMTYPE = SYS SIZE = BYTE SHARE = Yes MEMORY = 32K ;Video ROM ADDRESS = 0C0000h WRITABLE = NO MEMTYPE = SYS SIZE = BYTE SHARE = NO CACHE = YES