;
; Wangtek PC02 QIC-02 host adapter (Assy: 30631-001 Rev. C)
;
; 2003-07-29 by Michael Baeuerle (michael.baeuerle@gmx.net)
;

BOARD
   ID = "WTK0631"
   NAME = "Wangtek PC02"
   MFR = "Wangtek"
   CATEGORY = "MSD"
   SLOT = ISA8
   LENGTH = 120                                  ; Approximate length
   AMPERAGE = 1000                               ; 1A (appreciated)
   SKIRT = NO
   READID = NO
   DISABLE = UNSUPPORTED
   COMMENTS="This board contains a QIC-02 host adapter.\n
	     One internal and one external port is provided."
   HELP = "Written by Michael Baeuerle (michael.baeuerle@gmx.net)\n
           Select the desired hardware configuration. Then
           use the configuration utility \"View Switches and Jumpers\"
           option to verify that the jumpers and switches switch have been
           set correctly for this configuration."

JUMPER(1) = 1
   NAME = "W1"
   JTYPE = INLINE
   VERTICAL = NO
   REVERSE = YES 
   LABEL = LOC(2 1) "2" "1"
   FACTORY = LOC (1^2) 1
   COMMENTS = "This jumper inhibits DMA transfers when an error occurs."

JUMPER(2) = 1
   NAME = "W2"
   JTYPE = INLINE
   VERTICAL = NO
   REVERSE = NO 
   LABEL = LOC(1 2) "1" "2"
   FACTORY = LOC (1^2) 1
   COMMENTS = "This jumper connects board and chassis ground."

JUMPER(3) = 6
   NAME = "HDR1"
   JTYPE = PAIRED
   VERTICAL = NO
   REVERSE = YES
   LABEL = LOC(1-6) "2" "3" "4"
 "5" "6" "7"
   FACTORY = LOC(1-6) 000100
   COMMENTS = "The jumper block selects the IRQ line."

JUMPER(4) = 3
   NAME = "HDR2"
   JTYPE = PAIRED
   VERTICAL = NO
   REVERSE = YES
   LABEL = LOC(1-3) "DRQ1" "DRQ2" "DRQ3"
   FACTORY = LOC(1-3) 100
   COMMENTS = "The jumper block selects the DMA request line."

JUMPER(5) = 3
   NAME = "HDR3"
   JTYPE = PAIRED
   VERTICAL = NO
   REVERSE = YES
   LABEL = LOC(1-3) "DACK1" "DACK2" "DACK3"
   FACTORY = LOC(1-3) 100
   COMMENTS = "The jumper block selects the DMA acknoledge line."

SWITCH(1) = 10
   NAME = "SW1"
   STYPE = DIP
   VERTICAL = YES
   REVERSE = YES
   LABEL = LOC(1-10) "A1" "A2" "A3" "A4" "A5" "A6" "A7" "A8" "NC" "PS"
   FACTORY = LOC(1-10) 1111111001

FUNCTION = "QIC-02 Host Adapter"
   TYPE = "MSD"
   CONNECTION = "Sub-D38: External drive cable"

   SUBFUNCTION = "I/O Port Base Address"
      COMMENTS = "Select the host adapter I/O port base address.\n
                  Be sure the switches are in correct setting."
      HELP = "Selects the base address of the host adapter interface
              registers in the ISA I/O address space. The switches
              that select the I/O port base address on the host adapter
              are positions 1 to 8 on Switch SW1.  These switches must be
              configured to correspond with the chosen port address.
	      Use the configuration utility \"View Jumpers and Switches\"
	      option to determine the correct switch settings for your choice."
      CHOICE = "I/O Port 0280H"
         LINK
         PORT = 0280h-0281h
         INIT = SWITCH(1) LOC(1-10) 1111110101
      CHOICE = "I/O Port 0288H"
         LINK
         PORT = 0288h-0289h
         INIT = SWITCH(1) LOC(1-10) 1101110101
      CHOICE = "I/O Port 0300H"
         LINK
         PORT = 0300h-0301h
         INIT = SWITCH(1) LOC(1-10) 1111111001
      CHOICE = "I/O Port 0338H"
         LINK
         PORT = 0338h-0339h
         INIT = SWITCH(1) LOC(1-10) 1100011001

   SUBFUNCTION = "Interrupt Channel"
      COMMENTS = "Select the host adapter interrupt channel."
      HELP = "This jumper selects the interrupt channel which is used
              by the host adapter to request service from the host.
              The host adapter needs a dedicated interrupt channel.
	      Use the configuration utility \"View Jumpers and Switches\"
	      option to determine the correct jumper setting for your choice."
      CHOICE = "IRQ 2"
         LINK
         IRQ = 2
         TRIGGER = EDGE
         SHARE = NO
         INIT = JUMPER(3) LOC(1-6) 100000
      CHOICE = "IRQ 3"
         LINK
         IRQ = 3
         TRIGGER = EDGE
         SHARE = NO
         INIT = JUMPER(3) LOC(1-6) 010000
      CHOICE = "IRQ 4"
         LINK
         IRQ = 4
         TRIGGER = EDGE
         SHARE = NO
         INIT = JUMPER(3) LOC(1-6) 001000
      CHOICE = "IRQ 5"
         LINK
         IRQ = 5
         TRIGGER = EDGE
         SHARE = NO
         INIT = JUMPER(3) LOC(1-6) 000100
      CHOICE = "IRQ 6"
         LINK
         IRQ = 6
         TRIGGER = EDGE
         SHARE = NO
         INIT = JUMPER(3) LOC(1-6) 000010
      CHOICE = "IRQ 7"
         LINK
         IRQ = 7
         TRIGGER = EDGE
         SHARE = NO
         INIT = JUMPER(3) LOC(1-6) 000001

   SUBFUNCTION = "DMA Channel"
      COMMENTS = "Select the host adapter DMA channel."
      HELP = "This jumper selects the DMA channel which is used by
              the host adapter to transfer data from and to host memory.
              The host adapter needs a dedicated DMA channel.
	      Use the configuration utility \"View Jumpers and Switches\"
	      option to determine the correct jumper setting for your choice."
      CHOICE = "DMA 1"
         LINK
         DMA = 1
         SHARE = NO
         INIT = JUMPER(4) LOC(1-3) 100
         INIT = JUMPER(5) LOC(1-3) 100
      CHOICE = "DMA 2"
         LINK
         DMA = 2
         SHARE = NO
         INIT = JUMPER(4) LOC(1-3) 010
         INIT = JUMPER(5) LOC(1-3) 010
      CHOICE = "DMA 3"
         LINK
         DMA = 3
         SHARE = NO
         INIT = JUMPER(4) LOC(1-3) 001
         INIT = JUMPER(5) LOC(1-3) 001

   SUBFUNCTION = "Inhibit DMA on error"
      COMMENTS = "Select if DMA should be inhibited when an error occur."
      HELP = "Default is yes (Jumper installed)."
      CHOICE = "Yes"
         LINK
         INIT = JUMPER(1) LOC(1^2) 1
      CHOICE = "No"
         LINK
         INIT = JUMPER(1) LOC(1^2) 0

   SUBFUNCTION = "Chassis ground connection"
      COMMENTS = "Select if logic ground should be connected to chassis ground."
      HELP = "Default is yes (Jumper installed)."
      CHOICE = "Yes"
         LINK
         INIT = JUMPER(2) LOC(1^2) 1
      CHOICE = "No"
         LINK
         INIT = JUMPER(2) LOC(1^2) 0