BOARD
 ID="WDC1009"
 NAME="Western Digital WD1009V-MM1/MM2 Winchester Controller"
 MFR="Western Digital"
 CATEGORY="MSD"
 SLOT=ISA16
 LENGTH=330
 HELP="
 Use the V)iew D)etail by Slot mode to see Configuration
 Options.  Use E)dit Change F)unction to select Options."

JUMPER (5) = 15
 NAME="W5"
 JTYPE=PAIRED
 VERTICAL=NO
 REVERSE=YES
 LABEL=LOC(1-15) "1 | 2" "3 | 4" "5 | 6" "7 | 8" "9 |10" "11|12" "13|14" 
  "15|16" "17|18" "19|20" "21|22" "23|24" "25|26" "27|28" "29|30" 
   
 INITVAL=LOC(1-15) xxxxxxxxxxxxxxx
 FACTORY=LOC(1-15) 100000010000000
 COMMENTS="
[ W5 ]\t 0: Not jumpered, 1: jumpered\n
1 - 2\t1: enable 64k buffer\n
3 - 4\t1: disable alternate sector\n
5 - 6\t1: disable translation \n
7 - 8\t1: physical mode \n
9 -10\t1: 7byte ECC, 0: 4byte ECC\n
11-12\t1: disable caching.\n
13-14\t1: BIOS PROM 27C128\n
15-16\t1: 16-bit bus BIOS\n
17-18\t0: BIOS address at (c800:0)\n
19-20\t1: BIOS disable\n
21-24  21-22\t 23-24\tIRQ\n
\t0 \t0 \t14\n
\t0 \t1 \t15\n
\t1 \t0 \t12\n
\t1 \t1 \t11\n
25-26\t0: DMA6, 1: DMA7\n
27-28\t0: Primary IO address\n
29-30\t1: Controller disable"

 JUMPER (4) = 4
 NAME="W4"
 JTYPE=PAIRED
 VERTICAL=NO
 REVERSE=YES
 LABEL=LOC(1-4) "1 | 2" "3 | 4" "5 | 6" "7 | 8" 
 INITVAL=LOC(1-4) xxxx
 FACTORY=LOC(1-4) 0000
 COMMENTS ="
 W4 1-2 : in to disable the WD1009V floppy controller\n
 W4 3-4 : out for DMA2\n
 W4 5-6 : out for floppy primary address\n
 W4 7-8 : out for single speed drive "

JUMPER (2) = 1
 NAME="W2"
 JTYPE=TRIPOLE
 VERTICAL=YES
  LABEL=LOC(1) "1-2-3"
 FACTORY=LOC(1) 0
 COMMENTS="
 W2 1-2 : in for floppy disk drives - AT type  \n
 W2 2-3 : in for floppy disk drive - PS2 type "

JUMPER (3) = 1
 NAME="W3"
 JTYPE=PAIRED
 VERTICAL=YES
 LABEL=LOC(1)"1-2"
 FACTORY=LOC(1) 0
 COMMENTS="
 W3 1-2 : out for EISA autoconfiguration disable \n
 W3 2-3 : in for EISA autoconfiguration enable "

JUMPER (6) = 1
 NAME="W6"
 JTYPE=PAIRED
 VERTICAL=YES
 REVERSE=YES
 LABEL=LOC(1) "1-2"
 FACTORY=LOC(1) 0
 COMMENTS="
 W6 1-2:  in - card enabled by EISA host.\n
\tout - card enabled all times "

SOFTWARE(1)="
 Installation procedure: \n
 \t Run CF.EXE and set hard drive to type 1. \n
 \t Boot DOS, and run DEBUG. \n
 \t At debug prompt '-', Type G=C800:5 \n
 \t     (or CC00:5 if W5 17-18 is installed)"

FUNCTION="Fixed Disk Controller Options"
TYPE="MSD,DSKCTL"
HELP="Use E)dit Change F)unction to Select Options."

SUBFUNCTION="IO Address"
CHOICE="Primary"
 FREE
  PORT=1F0h-1F7h
;  PORT=3F6h -3F7h
;  SHARE=YES
  INIT=JUMPER(5)LOC(14-15) 00
CHOICE="Secondary"
 FREE
  PORT=170h-177h
  PORT=376h
  PORT=377h
  SHARE=YES
  INIT=JUMPER(5)LOC(14-15) 10
CHOICE="Disabled"
  FREE
  INIT=JUMPER(5)LOC(14-15) 01

SUBFUNCTION="DMA Channel"
CHOICE="DMA 6"
  FREE	
  INIT=JUMPER(5)LOC(13) 0
CHOICE="DMA 7"
  FREE	
  INIT=JUMPER(5)LOC(13) 1

SUBFUNCTION="Interrupt Request Line"
CHOICE="IRQ 14"
  FREE	
  INIT=JUMPER(5)LOC(11-12) 00
CHOICE="IRQ 15"
  FREE	
  INIT=JUMPER(5)LOC(11-12) 01
CHOICE="IRQ 12"
  FREE	
  INIT=JUMPER(5)LOC(11-12) 10
CHOICE="IRQ 11"
  FREE	
  INIT=JUMPER(5)LOC(11-12) 11

SUBFUNCTION="BIOS Memory Address"
CHOICE="C800:0"
  FREE	
  INIT=JUMPER(5)LOC(9-10) 00
CHOICE="CC00:0"
  FREE	
  INIT=JUMPER(5)LOC(9-10) 10
CHOICE="Disabled"
  FREE	
  INIT=JUMPER(5)LOC(9-10) 01

SUBFUNCTION="BIOS Bus Width"
CHOICE="16 Bit"
  FREE	
  INIT=JUMPER(5)LOC(8) 1
CHOICE="8 Bit"
  FREE	
  INIT=JUMPER(5)LOC(8) 0

SUBFUNCTION="BIOS Size"
CHOICE="16k (27C128)"
  FREE	
  INIT=JUMPER(5)LOC(7) 0
CHOICE="8k (27C64)"
  FREE	
  INIT=JUMPER(5)LOC(7) 1

FUNCTION="Fixed Disk Controller Operational Options"
HELP="Use E)dit Change F)unction to Select Options."

SUBFUNCTION="Caching"
CHOICE="Enabled"
  FREE	
  INIT=JUMPER(5)LOC(6) 0
CHOICE="Disabled"
  FREE	
  INIT=JUMPER(5)LOC(6) 1

SUBFUNCTION="ECC Length"
CHOICE="4-byte ECC"
  FREE	
  INIT=JUMPER(5)LOC(5) 0
CHOICE="7-byte ECC"
  FREE	
  INIT=JUMPER(5)LOC(5) 1

SUBFUNCTION="Sector Per Track"
CHOICE="Actual"
  FREE	
  INIT=JUMPER(5)LOC(4) 0
CHOICE="35 Sector Per Track"
  FREE	
  INIT=JUMPER(5)LOC(4) 1

SUBFUNCTION="Translation Mode"
CHOICE="Enabled"
  FREE	
  INIT=JUMPER(5)LOC(3) 0
CHOICE="Disabled"
  FREE	
  INIT=JUMPER(5)LOC(3) 1

SUBFUNCTION="Alternate Sector"
CHOICE="Disabled"
  FREE	
  INIT=JUMPER(5)LOC(2) 0
CHOICE="Enabled"
  FREE	
  INIT=JUMPER(5)LOC(2) 1

SUBFUNCTION="Controller Buffer Size"
CHOICE="64 K"
  FREE	
  INIT=JUMPER(5)LOC(1) 1
CHOICE="32 K"
  FREE	
  INIT=JUMPER(5)LOC(1) 0

FUNCTION="Floppy Disk Controller Options"
HELP="Use E)dit Change F)unction to Select Options."

SUBFUNCTION="Floppy Enable/Disable"
CHOICE="Enabled"
  FREE	
  INIT=JUMPER(4)LOC(1) 0
CHOICE="Disabled"
  FREE	
  INIT=JUMPER(4)LOC(1) 1

SUBFUNCTION="DMA Channel"
CHOICE="DMA 2"
  FREE	
  INIT=JUMPER(4)LOC(2) 0
CHOICE="DMA 3"
  FREE	
  INIT=JUMPER(4)LOC(2) 1

SUBFUNCTION="IO Address"
CHOICE="Primary"
 FREE
  PORT=3F0h-3F5h
  PORT=3F6h-3F7h
  SHARE=YES
  INIT=JUMPER(4)LOC(3) 0
CHOICE="Secondary"
 FREE
  PORT=370h-375h
  PORT=376h-377h
  SHARE=YES
  INIT=JUMPER(4)LOC(3) 1

SUBFUNCTION="Floppy Drive Speed"
CHOICE="Single Speed"
  FREE	
  INIT=JUMPER(4)LOC(4) 0
CHOICE="Dual Speed"
  FREE	
  INIT=JUMPER(4)LOC(4) 1

SUBFUNCTION="Floppy Drive Type"
CHOICE="PC-AT Type"
  FREE	
  INIT=JUMPER(4)LOC(1) 0
CHOICE="PS2 Type"
  FREE	
  INIT=JUMPER(4)LOC(1) 1

FUNCTION="EISA Autoconfiguration Mode"
HELP="Use E)dit Change F)unction to Select Options."

SUBFUNCTION="Autoconfiguration"
CHOICE="Disabled"
  FREE	
  INIT=JUMPER(3)LOC(1) 0
CHOICE="Enabled"
  FREE	
  INIT=JUMPER(3)LOC(1) 1

SUBFUNCTION="Card Enable Control"
CHOICE="Always"
  FREE	
  INIT=JUMPER(6)LOC(1) 0
CHOICE="By EISA Host"
  FREE	
  INIT=JUMPER(6)LOC(1) 1