; TCO5047 EISA SONIC CFG file
; v. 1.0S1 (930720)
; v. 1.0d2 (930820) cdm
BOARD
  ID   = "TCO5047"
  NAME = "TC5047 Thomas-Conrad Ethernet EISA Adapter"
  MFR  = "Thomas-Conrad Corporation"
  CATEGORY = "NET"
  SLOT = EISA
  LENGTH = 157
  READID = YES
  BUSMASTER = 23
  AMPERAGE = 600
  IOCHECK = INVALID
  DISABLE = SUPPORTED
  COMMENTS = 
	 "The TC5047 is a 32-bit Ethernet Adapter designed
	  for the EISA bus.  The TC5047 is fully software
	  configurable and uses a bus mastering design.  This
	  bus mastering design uses the host system main
	  memory directly for increased performance.\n
	  After the card is installed and configured using the EISA
	  Configuration Utility, the Thomas-Conrad EtherTools 
	  utility can then be used to verify the correct operation 
	  of the adapter."

IOPORT(1) = 0zc88h  INITVAL = 01x1xxxx  ; slave size=16, master size=32
IOPORT(2) = 0zc89h  INITVAL = 0000xxx1
IOPORT(3) = 0zc8Ah  INITVAL = xxxx0000
IOPORT(4) = 0zc8Fh  INITVAL = 00000000

FUNCTION      = "Interrupt Request (IRQ) Mode"
  COMMENTS    = "Select the Interrupt mode used by the adapter.
		 To change the interrupt number, select Edit Resource.\n"
  HELP        = "The default Shareable option allows the IRQ selected for
		 this TC5047 to be shared with other TC5047 adapters.  The
		 Non-Shareable option prevents the IRQ selected for this
		 TC5047 to be shared with any other adapters.  To change
		 the IRQ request line, select the Edit or Change Resource
		 option in your configuration program.\n"
  CHOICE      = "Non-Shareable IRQ (Default)"
    LINK
    IRQ       = 3|5|9|10
    INIT      = IOPORT(1)LOC(2-0)001|011|101|111
  CHOICE      = "Shareable IRQ"
    LINK
    IRQ       = 3|5|9|10
    SHARE     = "TCO5047"
    TRIGGER   = LEVEL
    INIT      = IOPORT(1)LOC(2-0)000|010|100|110

FUNCTION = "Remote Reset ROM"
  COMMENTS = "If no ROM is installed leave this function
	      at disabled.  If you are installing a ROM from
	      Thomas-Conrad you will need to change the selection
	      to enabled."
  HELP     = "If no ROM is installed leave this function
	      at disabled.  If you are installing a ROM from
	      Thomas-Conrad you will need to change the selection
	      to enabled."
  CHOICE = "ROM Disabled      (Default)"
	  FREE
	  INIT = IOPORT(3) LOC(7-6) 00
  CHOICE = "Enabled"
    FREE
	  INIT = IOPORT(3) LOC(7-6) 11
	  LINK
	    MEMORY = 32K
      ADDRESS = 0C8000H|0D0000H|0D8000H|0C0000H
	    WRITABLE = NO
	    MEMTYPE = OTHER
	    SIZE = BYTE
	    DECODE = 24
	    CACHE = YES
	    INIT = IOPORT(3) LOC(5-4) 01|10|11|00

FUNCTION = "Bus Master Timing"
  HELP = "The Short option causes a bus preemption release after 696
	  nanoseconds, which is an acceptable default for most systems.
	  If you experience inconsistent results or data loss, change
	  this setting to Long."
  CHOICE = "Short             (Default)"
	  FREE
	  INIT = IOPORT(1) LOC(5) 0

  CHOICE = "Long"
	  FREE
	  INIT = IOPORT(1) LOC(5) 1

FUNCTION = "Media"
   SUBFUNCTION = "Media Selection"
   HELP = "This selection configures the TC5047-TIO to use
	  Twisted Pair (10baseT), Thin Coax (10base2) or
	  the AUI Port.  The TC5047-T only has a connector
	  for 10BaseT.  When configuring the TC5047-T make
	  make sure that this option is set for 10BaseT or
	  the card will not work."
  CHOICE = "Twisted Pair - 10base-T "
	  FREE
    INIT = IOPORT(2) LOC(2-1) 11
  CHOICE = "Thin Coax - 10base2 "
	  FREE
    INIT = IOPORT(2) LOC(2-1) 00
  CHOICE = "AUI connection "
	  FREE
    INIT = IOPORT(2) LOC(2-1) 01

FUNCTION ="Distance (10baseT only)"
   HELP = "The Distance selection option is used only with Twisted
	   Pair (10baseT). The concentrator that the card is
	   connected to must be capable of supporting extended distance."
  CHOICE = "Normal"
    FREE
    INIT = IOPORT(2) LOC(3) 0
  CHOICE = "Extended"
    FREE
    INIT = IOPORT(2) LOC(3) 1