BOARD ID = "TCO345A" NAME = "TC3045 Thomas-Conrad Network System (TCNS) AT Adapter" MFR = "Thomas-Conrad Corporation" CATEGORY = "NET" SLOT = ISA16 LENGTH = 340 SKIRT = NO READID = NO AMPERAGE = 2900 IOCHECK = INVALID COMMENTS = "The Workstation Memory, Node and I/O Address must be configure by setting SW1, SW2 and SW3 respectively. See manual for details. Caution should be used when specifying an IRQ, as it may be used by another device. For example, IRQ15 could be used by diskette drives and IRQ7 could be used by printers." HELP = "Discrete logic implementations of this card using surface mount and/or through hole technology must use file name !TCO345A.CFG." SWITCH(1) = 8 NAME = "SW1" STYPE = dip VERTICAL = yes REVERSE = yes FACTORY = LOC(1-8) 00101111 COMMENTS = "SW1 must be set according to the picture shown so the card setting matches your computer configuration." SWITCH(2) = 8 STYPE = dip NAME = "SW2" VERTICAL = yes REVERSE = yes FACTORY = LOC(1-8) 01111111 COMMENTS = "SW2 must be set according to the picture shown so the card setting matches your computer configuration." SWITCH(3) = 8 STYPE = dip NAME = "SW3" VERTICAL = yes REVERSE = yes FACTORY = LOC(1-8) 01000111 COMMENTS = "SW3 must be set according to the picture shown so the card setting matches your computer configuration." JUMPER(1) = 11 NAME = "IRQ Blocks" JTYPE = paired REVERSE = YES LABEL = LOC(1 2 3 4 5 6 7 8 9 10 11) "IRQ14" "IRQ15" "IRQ12" "IRQ11" "IRQ10" "IRQ3" "IRQ4" "IRQ5" "IRQ6" "IRQ7" "IRQ9" FACTORY = LOC(1-11) 00000000001 COMMENTS = "IRQ jumper must be set according to the picture shown so the card setting matches your computer configuration." JUMPER(2) = 1 NAME = "Wait State" JTYPE = paired LABEL = LOC(1) "WS" FACTORY = LOC(1) 1 COMMENTS = "Wait State jumper must be set according to the picture shown so the card setting matches your computer configuration." JUMPER(3) = 1 NAME = "Memory Block Decode" JTYPE = tripole VERTICAL = YES LABEL = LOC(1) "128K/16K" FACTORY = LOC(1) 1 COMMENTS = "Memory Block Decode jumper must be set according to the picture shown so the card setting matches your computer configuration." FUNCTION = "TCNS Adapter Configuration" COMMENTS = "When enhanced mode is selected, LOC7 of SW3 must be in the ON position. When compatible mode is selected, LOC7 of SW3 must be in the OFF position." HELP = "Memory, I/O, and interrupt conflicts will not allow the adapter to operate properly or operate at all. TCCARC must be used when the adapter is set to ENHANCED mode; GXLARC or any other ARCNET driver must be used when the adapter is set to compatible mode." CHOICE = "Enhanced Mode" LINK IRQ = 9 | 7 | 6 | 5 | 4 | 3 | 10 | 11 | 12 | 15 | 14 SHARE = NO TRIGGER = LEVEL INIT = JUMPER(1) LOC(1-11) 00000000001 | 00000000010 | 00000000100 | 00000001000 | 00000010000 | 00000100000 | 00001000000 | 00010000000 | 00100000000 | 01000000000 | 10000000000 COMBINE MEMORY = 16k ADDRESS = 0d0000h | 0d4000h | 0d8000h | 0dc000h | 0c0000h | 0c4000h | 0c8000h | 0cc000h MEMTYPE = oth SIZE = word DECODE = 24 INIT = SWITCH(1) LOC(1-8) 00101111 | 00101011 | 00100111 | 00100011 | 00111111 | 00111011 | 00110111 | 00110011 FREE INIT = SWITCH(3) LOC(1-8) 01000111 FREE INIT = JUMPER(2) LOC(1) 1 FREE INIT = JUMPER(3) LOC(1) 1 CHOICE = "Compatible Mode" LINK IRQ = 14 | 15 | 12 | 11 | 10 | 3 | 4 | 5 | 6 | 7 | 9 SHARE = NO TRIGGER = LEVEL INIT = JUMPER(1) LOC(1- 11) 10000000000 | 01000000000 | 00100000000 | 00010000000 | 00001000000 | 00000100000 | 00000010000 | 00000001000 | 00000000100 | 00000000010 | 00000000001 LINK PORT = 02e0h-02efh | 02f0h-02ffh | 0300h-030fh | 0350h-035fh INIT = SWITCH(3) LOC(1-8) 01000101 | 01000001 | 00111101 | 00101001 COMBINE MEMORY = 16k ADDRESS = 0d0000h | 0d4000h | 0d8000h | 0dc000h | 0c0000h | 0c4000h | 0c8000h | 0cc000h MEMTYPE = oth SIZE = word DECODE = 24 INIT = SWITCH(1) LOC(1-8) 00101111 | 00101011 | 00100111 | 00100011 | 00111111 | 00111011 | 00110111 | 00110011 FREE INIT = JUMPER(2) LOC(1) 1 FREE INIT = JUMPER(3) LOC(1) 1 FUNCTION = "TC3045 Node ID Upper Nibble Options" COMMENTS = "This option sets the four most significant bits of the Node ID byte. Node ID selection will be completed when the four least significant bits are set in the next option. If this option is set to Bh, the Node ID will be 176 plus the value of the next option." HELP = "Every adapter in a TCNS Network must have a unique source identification number or Node ID. The node ID can be any available number between 1 and 255. EISA systems can not detect conflicts of network resources. NODE ID conflicts can be detected with the aid of a TCNS HUB. Multiple network reconfigurations and packet retransmissions might be a sign of duplicate node IDs. See TCNS User's Manual for more details." CHOICE = "Upper Nibble 0Xh (0)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 1111 CHOICE = "Upper Nibble 1Xh (16)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 1110 CHOICE = "Upper Nibble 2Xh (32)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 1101 CHOICE = "Upper Nibble 3Xh (48)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 1100 CHOICE = "Upper Nibble 4Xh (64)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 1011 CHOICE = "Upper Nibble 5Xh (80)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 1010 CHOICE = "Upper Nibble 6Xh (96)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 1001 CHOICE = "Upper nibble 7Xh (112)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 1000 CHOICE = "Upper Nibble 8Xh (128)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 0111 CHOICE = "Upper Nibble 9Xh (144)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 0110 CHOICE = "Upper Nibble AXh (160)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 0101 CHOICE = "Upper Nibble BXh (176)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 0100 CHOICE = "Upper Nibble CXh (192)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 0011 CHOICE = "Upper Nibble DXh (208)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 0010 CHOICE = "Upper Nibble EXh (224)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 0001 CHOICE = "Upper Nibble FXh (240)" FREE INIT = SWITCH(2) LOC(8 7 6 5) 0000 FUNCTION = "TC3045 Node ID Lower Nibble Options" COMMENTS = "This option sets the four least significant bits of the Node ID byte. Node ID selection will be completed when the four most significant bits are set in the previous option. If this option is set to Ch, the Node ID will be set to 12 plus the value of the previous option." HELP = "To set this adapter node ID to 73 the upper nibble must be set to 4h (64) and the lower nibble must be set to 9h. Never set the upper and lower nibble to 0h because Node ID 0 (00h) is not allowed in a TCNS network." CHOICE = "Lower Nibble X1h (1)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 1110 CHOICE = "Lower Nibble X2h (2)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 1101 CHOICE = "Lower Nibble X3h (3)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 1100 CHOICE = "Lower Nibble X4h (4)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 1011 CHOICE = "Lower Nibble X5h (5)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 1010 CHOICE = "Lower Nibble X6h (6)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 1001 CHOICE = "Lower Nibble X7h (7)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 1000 CHOICE = "Lower Nibble X8h (8)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 0111 CHOICE = "Lower Nibble X9h (9)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 0110 CHOICE = "Lower Nibble XAh (10)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 0101 CHOICE = "Lower Nibble XBh (11)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 0100 CHOICE = "Lower Nibble XCh (12)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 0011 CHOICE = "Lower Nibble XDh (13)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 0010 CHOICE = "Lower Nibble XEh (14)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 0001 CHOICE = "Lower Nibble XFh (15)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 0000 CHOICE = "Lower Nibble X0h (0)" FREE INIT = SWITCH(2) LOC(4 3 2 1) 1111