; SIEMENS NIXDORF 32-Bit Bus Master 82596 Ethernet Controller AUI/10 Base T
; Config File: !SNIAAA0.CFG  V1.5
; 3.6.93

BOARD
   ID = "SNIAAA0"
   NAME = "SIEMENS NIXDORF Ether-Board EISA T"
   MFR = "SIEMENS NIXDORF"
   CATEGORY = "NET"
   SLOT = EISA
   LENGTH = 155
   READID = yes
   BUSMASTER = 40  ; Bus latency time allowed (50 us)
   AMPERAGE = 1500
   IOCHECK = INVALID
   DISABLE = SUPPORTED

   COMMENTS = "	This EISA Bus Master Board is a 32 bit Ethernet Adaptor 
		based on the Intel 82596CA. The board supports network
		connection for AUI and 10 Base T."

   HELP = "For further information please refer to the manual and the readme
           files on the driver disks."

IOPORT(1) = 0zc88h
; 82596CA-Einstellungen: Data Size Slave/Master jeweils 32 Bit
; EISA Bus Release After Preempt 23 BCLK
; Unlatched Interrupt

	INITVAL = LOC(7 6 5 3) 1100

IOPORT(2) = 0zc89h
; Nur slotspezifische IO-Adressen verwenden

	INITVAL = LOC(7-4) 0000


IOPORT(3) = 0zc8Ah

IOPORT(4) = 0zc8Fh

IOPORT(5) = 0zc84h


;=============================================================================

FUNCTION = "Ethernet Interrupt Number and Type"

   COMMENTS = "\nThis board supports interrupts 10, 11, 5, and 9.
		The interrupt can be edge or level triggered.
		However, note that level triggered mode must be 
                    supported by the driver software. Edge triggered mode
                    will work in any case.\n"
	      
      CHOICE = "Edge Triggered Interrupt 10"
      LINK
        IRQ = 10
        TRIGGER = EDGE
        SHARE = NO
        INIT = IOPORT(1) LOC(2-0) 101

      CHOICE = "Edge Triggered Interrupt 5"
      LINK
        IRQ = 5
        TRIGGER = EDGE
        SHARE = NO
        INIT = IOPORT(1) LOC(2-0) 001

      CHOICE = "Edge Triggered Interrupt 11"
      LINK
        IRQ = 11
        TRIGGER = EDGE
        SHARE = NO
        INIT = IOPORT(1) LOC(2-0) 111

      CHOICE = "Edge Triggered Interrupt 9"
      LINK
        IRQ = 9
        TRIGGER = EDGE
        SHARE = NO
        INIT = IOPORT(1) LOC(2-0) 011

      CHOICE = "Level Triggered Interrupt 10"
      LINK
        IRQ = 10
        TRIGGER = LEVEL
        SHARE = YES
        INIT = IOPORT(1) LOC(2-0) 100

      CHOICE = "Level Triggered Interrupt 5"
      LINK
        IRQ = 5
        TRIGGER = LEVEL
        SHARE = YES
        INIT = IOPORT(1) LOC(2-0) 000

      CHOICE = "Level Triggered Interrupt 11"
      LINK
        IRQ = 11
        TRIGGER = LEVEL
        SHARE = YES
        INIT = IOPORT(1) LOC(2-0) 110
        
      CHOICE = "Level Triggered Interrupt 9"
      LINK
        IRQ = 9
        TRIGGER = LEVEL
        SHARE = YES
        INIT = IOPORT(1) LOC(2-0) 010


;=============================================================================

FUNCTION = "Ethernet Connector Selection"
   CONNECTION = "AUI (15 pin D) or 10 Base T (RJ45)"

      CHOICE = "Automatic Selection"
	FREE
	INIT = IOPORT(2) LOC(1) 1


      CHOICE = "AUI Connector"
	FREE
	INIT = IOPORT(2) LOC(1-0) 00

      CHOICE = "10 Base T Connector"
	FREE
	INIT = IOPORT(2) LOC(1-0) 01


;=============================================================================

FUNCTION = "Remote Boot PROM"
   COMMENTS = "This board supports an optional remote boot PROM.\n
		For more information and availability please\n
		contact your local dealer. \n"

      CHOICE = "Disabled"
	FREE
	INIT = IOPORT(3) LOC(7-6) 00

      CHOICE = "Enabled"
	LINK
	MEMORY = 32K
	ADDRESS = 0C0000H | 0C8000H | 0D0000H | 0D8000H 
	WRITABLE = NO
	MEMTYPE = OTHER
	SIZE = BYTE
	DECODE = 24
	CACHE = YES
	INIT = IOPORT(3) LOC(7-4) 1100 | 1101 | 1110 | 1111