;
; Star Gate Technologies Inc. - ACL II (16k)
;

BOARD
	ID="SGT0010"
	NAME="ACL II - Serial Card w/16k RAM"
	MFR="Star Gate"
	CATEGORY="COM"
	SLOT=ISA16
	LENGTH=330
	SKIRT=NO
	READID=NO
	COMMENTS="Star Gate ACL II with 16k dual port RAM."

SWITCH(1)=8
	NAME="SW1"
	STYPE=DIP
	VERTICAL=NO
	REVERSE=YES
	FACTORY=LOC(1-8)00000000
	LABEL=LOC(1-8) "irq3" "irq4" "irq5" "irq9" "irq10" "irq11" "irq12" "irq15"
	COMMENTS="This switch is located just above the gold plated
 edge connector.  It is used to set the board IRQ level."
	
SWITCH(2)=4
	NAME="SW2"
	STYPE=DIP
	VERTICAL=NO
	REVERSE=YES
	FACTORY=LOC(1-4)0000
	COMMENTS="This switch is located just above the gold plated
 edge connector.  Positions 1 and 2 are used to set the board I/O
 latch addresses. Position 3 determines whether the board's Dual Port
will be mapped above or below the 1 Meg boundary."
	
JUMPER(1)=8
	NAME="JP2"
	JTYPE=PAIRED
	VERTICAL=NO
	REVERSE=YES
	LABEL=LOC(1-8) "1" "2" "3" "4" "5" "6" "7" "8"
	FACTORY=LOC(1-8) 10000000
	INITVAL=LOC(1-8) 01000000
	COMMENTS="This jumper is located above and to the left of the gold
plated edge connector. It is used to select the number of wait states
required by the host computer. Position 1 inserts zero wait states, position
2 selects one wait state, and so on. If you are using an 8 Mhz backplane it
is suggested that you set the jumper to position 2 for one wait state. "

FUNCTION="IRQ Level"
	TYPE="COM,ASY"
	COMMENTS=" The ACL II can be configured to use IRQs 3,4,5,9,10,11,12,15"

	CHOICE="irq 3"
		LINK
		IRQ=3
		SHARE=NO
		INIT=SWITCH(1) LOC(1-8) 10000000

	CHOICE="irq 4"
		LINK
		IRQ=4
		SHARE=NO
		INIT=SWITCH(1) LOC(1-8) 01000000

	CHOICE="irq 5"
		LINK
		IRQ=5
		SHARE=NO
		INIT=SWITCH(1) LOC(1-8) 00100000

	CHOICE="irq 9"
		LINK
		IRQ=9
		SHARE=NO
		INIT=SWITCH(1) LOC(1-8) 00010000

	CHOICE="irq 10"
		LINK
		IRQ=10
		SHARE=NO
		INIT=SWITCH(1) LOC(1-8) 00001000

	CHOICE="irq 11"
		LINK
		IRQ=11
		SHARE=NO
		INIT=SWITCH(1) LOC(1-8) 00000100

	CHOICE="irq 12"
		LINK
		IRQ=12
		SHARE=NO
		INIT=SWITCH(1) LOC(1-8) 00000010

	CHOICE="irq 15"
		LINK
		IRQ=15
		SHARE=NO
		INIT=SWITCH(1) LOC(1-8) 00000001

	CHOICE="Disable IRQ"
		DISABLE = YES
		FREE
		INIT=SWITCH(1) LOC(1-8) 00000000

FUNCTION="I/O Latch Address"
	CHOICE="200h,204h"
		LINK
		PORT=0200h
		SHARE=NO
		SIZE=BYTE
		PORT=0204h
		SHARE=NO
		SIZE=BYTE
		INIT=SWITCH(2) LOC(1 2 3 4) 0000

	CHOICE="300h,304h"
		LINK
		PORT=0300h
		SHARE=NO
		SIZE=BYTE
		PORT=0304h
		SHARE=NO
		SIZE=BYTE
		INIT=SWITCH(2) LOC(1 2 3 4) 1000

	CHOICE="600h,604h"
		LINK
		PORT=0600h
		SHARE=NO
		SIZE=BYTE
		PORT=0604h
		SHARE=NO
		SIZE=BYTE
		INIT=SWITCH(2) LOC(1 2 3 4) 0100

	CHOICE="700h,704h"
		LINK
		PORT=0700h
		SHARE=NO
		SIZE=BYTE
		PORT=0704h
		SHARE=NO
		SIZE=BYTE
		INIT=SWITCH(2) LOC(1 2 3 4) 1100

FUNCTION="Dual Port RAM Address"
COMMENTS = "Select 'Change Resources' from the Edit pull-down
 menu to change the selections for this function.
\nSelect 'View Resources' to verify the selected addresses and IRQ
 lines.\n"
	CHOICE="Dual Port Address"
		LINK
		MEMORY=16K
		ADDRESS=0A0000h-0FF0000h STEP=16K
		WRITABLE=YES
		MEMTYPE=OTHER
		SHARE=NO