;
;  SAMSUNG VGA Card
;
BOARD          
 ID="SEC0020"
 NAME="SAMSUNG VGA Card (GTI VC-004)"
 MFR="SAMSUNG Electronics"
 CATEGORY="VID"
 SLOT=ISA8OR16
 LENGTH=215
 COMMENTS = " This is a SAMSUNG VGA card using VC-004 from GEMINI Technology"
 HELP="The SAMSUNG VGA Card supports manually selectable configuration.
     \n
     \nMonitor type can be selected by DIP Switch LOC (1-4).
     \n   
     \nMode type can be selected by DIP Switch LOC (8).
     \n   
     \nTrap Interrupt can be enabled or disabled by JUMPER 3.
     \n   
     \nTTL monitor type can be selected by JUMPER 5.
     \n   
     \nMemory Configuration can be selected by JUMPER 6.
     \n   
     \nMemory Device type can be selected by JUMPER 7.
     \n   
     \n8bit, 16bit Mode can be selected by JUMPER 8
     \n   
     \nVertical Interrupt can be enabled or disabled by JUMPER 9."

SWITCH(1) = 8
  NAME="SW1"
  STYPE=DIP
  REVERSE=YES
  VERTICAL=NO
  FACTORY=LOC(1-8) 01100000
  COMMENTS="SW1 LOC (1-4) selects a monitor type.
          \n
          \n   a) ECD High-Resolution  : LOC(1-4) 0110
          \n   b) ECD Low-Resolution   : LOC(1-4) 1110
          \n   c) RGB 40 * 25          : LOC(1-4) 1001
          \n   d) RGB 80 * 25          : LOC(1-4) 0001
          \n   e) Monochrome           : LOC(1-4) 0010
          \n
          \nSW1 LOC (5-6) are reserved for future use,
          \n              please leave in the off position.
          \nSW1 LOC (7)   selects a PS/2 or Multi-freq Monitor type.
          \nSW1 LOC (8)   selects a mode type."
  HELP=""
  
JUMPER(3) = 2
  NAME = "P3"             
  JTYPE = INLINE
  REVERSE = YES
  VERTICAL = YES
  FACTORY = LOC(1^2 2^3) 10
  COMMENTS = "This JUMPER used to enable Trap Interrupt
         \n
         \n   a) Enables  NMI requests : LOC (1^2 2^3) 10 
         \n   b) Disables NMI requests : LOC (1^2 2^3) 01"

  HELP = ""
  
JUMPER(5) = 2
  NAME = "P5"
  JTYPE = INLINE
  REVERSE = YES
  VERTICAL = YES
  FACTORY = LOC(1^2 2^3) 10
  COMMENTS = "This JUMPER used to select TTL monitor type
        \n
        \n   a) Color compatible (RGB/ECD/MFM) : LOC (1^2 2^3) 10     
        \n   b) Monochrome monitor compatible  : LOC (1^2 2^3) 01"
  HELP = ""
    
JUMPER(6) = 2
  NAME = "P6"
  JTYPE = INLINE
  REVERSE = YES
  VERTICAL = NO
  FACTORY = LOC(1^2 2^3) 10
  COMMENTS = "This JUMPER used to select Memory Configuration
        \n
        \n   a) 256KB(8 of 64K*4)  : LOC (1^2 2^3) 10 
        \n   b) 512KB or 1024KB    : LOC (1^2 2^3) 01" 
  HELP = ""
    
JUMPER(7) = 2
  NAME = "P7"
  JTYPE = INLINE
  REVERSE = YES
  VERTICAL = NO
  FACTORY = LOC(1^2 2^3) 10
  COMMENTS = "This JUMPER used to select Memory Device Type
        \n
        \n   a) 8 of 64K*4 or 16 of 64K*4 : LOC (1^2 2^3) 10    
        \n   b) 8 of 256K*4               : LOC (1^2 2^3) 01"
  HELP = ""

JUMPER(8) = 3
  NAME = "P8"
  JTYPE = INLINE
  REVERSE = YES
  VERTICAL = NO
  FACTORY = LOC(1^2 2^3 3^4) 001
  COMMENTS = "This JUMPER used to select 8/16 bit
        \n
        \n   a) Auto 8/16bit enable : LOC (1^2 2^3 3^4) 001 
        \n   b) 8bit enable         : LOC (1^2 2^3 3^4) 100
        \n   c) 16bit enable        : LOC (1^2 2^3 3^4) 010" 
  HELP = ""
    
JUMPER(9) = 2
  NAME = "P9"
  JTYPE = INLINE
  REVERSE = YES
  VERTICAL = YES
  FACTORY = LOC(1^2 2^3) 10
  COMMENTS = "This JUMPER used to enable Vertical Interrupt
        \n
        \n   a) IRQ2 enabled  : LOC (1^2 2^3) 10
        \n   b) IRQ2 disabled : LOC (1^2 2^3) 01"
         HELP = ""

FUNCTION = "Select Monitor type"
  TYPE = "VID"
  COMMENTS = " This SWITCH LOC (1-4) is used to select Monitor type"
  HELP = "
        \n After modified, user must change the JUMPERs &
        \n SWITCH on the SAMSUNG VGA card."
  
  CHOICE = "ECD High-Resolution"
    HELP= "
       \n JUMPER & SWITCH Setting is like this.
       \n
       \n  a) ECD High-Resolution
       \n
       \n     : SWITCH(1) LOC(1-4) 0110"
    LINK
      INIT = SWITCH(1) LOC (1-4) 0110

  CHOICE = "ECD Low-Resolution"
    HELP= "
       \n  b) ECD Low-Resolution
       \n
       \n     : SWITCH(1) LOC(1-4) 1110"

    LINK
      INIT = SWITCH(1) LOC (1-4) 1110

  CHOICE = "RGB 40 * 25"
    HELP= "
       \n  c) RGB 40 * 25
       \n
       \n     : SWITCH(1) LOC(1-4) 1001"
    
    LINK
      INIT = SWITCH(1) LOC (1-4) 1001

  CHOICE = "RGB 80 * 25"
    HELP= "
       \n  d) RGB 80 * 25
       \n
       \n     : SWITCH(1) LOC(1-4) 0001"

    LINK
      INIT = SWITCH(1) LOC (1-4) 0001

  CHOICE = "Monochrome"
    HELP= "
       \n  e) Monochrome
       \n
       \n     : SWITCH(1) LOC(1-4) 0010"
    LINK
      INIT = SWITCH(1) LOC (1-4) 0010
       
FUNCTION = "Select Mode type"
  TYPE = "VID"
  COMMENTS = " This SWITCH 8 is used to select Mode type"
  HELP = "
        \n After modified, user must change the JUMPERs &
        \n SWITCH on the SAMSUNG VGA card."
  
  CHOICE = "VGA"
    HELP= "
       \n JUMPER & SWITCH Setting is like this.
       \n
       \n  a) VGA
       \n
       \n     : SWITCH(1) LOC (8) 0" 
    LINK
      INIT = SWITCH(1) LOC (8) 0

  CHOICE = "EGA"
    HELP= "
       \n  b) EGA
       \n
       \n     : SWITCH(1) LOC(8) 1"
    LINK
      INIT = SWITCH(1) LOC (8) 1


FUNCTION = "Trap Interrupt Enable"
  TYPE = "VID"
  COMMENTS = " This JUMPER used to enable Trap Interrupt"
  HELP = "
        \n After modified, user must change the JUMPERs &
        \n SWITCH on the SAMSUNG VGA card."
  
  CHOICE = "Enables NMI requests by the VC-004"
    HELP= "
       \n JUMPER & SWITCH Setting is like this.
       \n
       \n  a) Enables NMI requests by the VC-004
       \n
       \n     : JUMPER(3) LOC (1^2 2^3) 10" 

    LINK 
      INIT = JUMPER(3) LOC (1^2 2^3) 10

  CHOICE = "Disables NMI requests by the VC-004"
    HELP = "
       \n  b) Disables NMI requests by the VC-004
       \n
       \n     : JUMPER(3) LOC (1^2 2^3) 01"
    LINK 
      INIT = JUMPER(3) LOC (1^2 2^3) 01

FUNCTION = "Select TTL monitor type"
  TYPE = "VID"
  COMMENTS = " This JUMPER used to select TTL monitor type"
  HELP = "
        \n After modified, user must change the JUMPERs &
        \n SWITCH on the SAMSUNG VGA card."
  
  CHOICE = "TTL color monitor compatible (RGB/ECD/MFM)"
    HELP= "
       \n JUMPER & SWITCH Setting is like this.
       \n
       \n  a) TTL color monitor compatible (RGB/ECD/MFM)
       \n
       \n     : JUMPER(5) LOC (1^2 2^3) 10"        
    LINK 
      INIT = JUMPER(5) LOC (1^2 2^3) 10

  CHOICE = "TTL monochrome monitor compatible"
    HELP = "
       \n  b) TTL monochrome monitor compatible
       \n
       \n     : JUMPER LOC (1^2 2^3) 01"
    LINK 
      INIT = JUMPER(5) LOC (1^2 2^3) 01
      
FUNCTION = "Memory Configuration select"
  TYPE = "VID"
  COMMENTS = "This JUMPER used to select Memory Configuration"
  HELP = "
        \n After modified, user must change the JUMPERs &
        \n SWITCH on the SAMSUNG VGA card."
  
  CHOICE = "256KB(8 of 64K*4)"
    HELP= "
       \n JUMPER & SWITCH Setting is like this.
       \n
       \n  a) 256KB(8 of 64K*4)
       \n
       \n     : JUMPER(6) LOC (1^2 2^3) 10" 
    LINK 
      INIT = JUMPER(6) LOC (1^2 2^3) 10

  CHOICE = "512KB(16 of 64K*4) or 1024KB(8 of 256K*4)"
    HELP = "
       \n  b) 512KB(16 of 64K*4) or 1024KB(8 of 256K*4)
       \n
       \n     : JUMPER(6) LOC (1^2 2^3) 01" 
    
    LINK 
      INIT = JUMPER(6) LOC (1^2 2^3) 01
          
FUNCTION = "Memory Device type"
  TYPE = "VID"
  COMMENTS = " This JUMPER used to select Memory Device type"
  HELP = "
        \n After modified, user must change the JUMPERs &
        \n SWITCH on the SAMSUNG VGA card."
  
  CHOICE = "8 of 64K*4 or 16 of 64K*4"
    HELP= "
       \n JUMPER & SWITCH Setting is like this.
       \n
       \n  a) 8 of 64K*4 or 16 of 64K*4
       \n
       \n     : JUMPER(7) LOC (1^2 2^3) 10"
    LINK 
      INIT = JUMPER(7) LOC (1^2 2^3) 10

  CHOICE = "8 of 256K*4"
    HELP = "
       \n  b) 8 of 256K*4 
       \n
       \n     : JUMPER(7) LOC (1^2 2^3) 01"
    
    LINK 
      INIT = JUMPER(7) LOC (1^2 2^3) 01
    
FUNCTION = "8/16 bit selection"
  TYPE = "VID"
  COMMENTS = " This JUMPER used to select 8bit mode, 16bit mode,
               or 8/16bit mode                                   "
  HELP = "
        \n After modified, user must change the JUMPERs &
        \n SWITCH on the SAMSUNG VGA card."
  
  CHOICE = "Auto 8/16bit enable"
    HELP= "
       \n JUMPER & SWITCH Setting is like this.
       \n
       \n  a) Auto 8/16bit enable
       \n
       \n     : JUMPER(8) LOC (1^2 2^3 3^4) 001" 
    LINK 
      INIT = JUMPER(8) LOC (1^2 2^3 3^4) 001

  CHOICE = "8bit enable"
    HELP = "
       \n  b) 8bit enable
       \n
       \n     : JUMPER(8) LOC (1^2 2^3 3^4) 100" 
    
    LINK 
      INIT = JUMPER(8) LOC (1^2 2^3 3^4) 100

  CHOICE = "16bit enable"
    HELP = "
       \n  c) 16bit enable
       \n
       \n     : JUMPER(8) LOC (1^2 2^3 3^4) 010" 
    
    LINK 
      INIT = JUMPER(8) LOC (1^2 2^3 3^4) 010
      
      
FUNCTION = "Vertical Interrupt Enable"
  TYPE = "VID"
  COMMENTS = " This JUMPER used to enable Vertical Interrupt"
  HELP = "
        \n After modified, user must change the JUMPERs &
        \n SWITCH on the SAMSUNG VGA card."
  
  CHOICE = "IRQ2 enabled"
    HELP= "
       \n JUMPER & SWITCH Setting is like this.
       \n
       \n  a) IRQ2 enabled
       \n
       \n     : JUMPER(9) LOC (1^2 2^3) 10"
    LINK 
      INIT = JUMPER(9) LOC (1^2 2^3) 10

  CHOICE = "IRQ2 disabled"
    HELP = "
       \n  b) IRQ2 disabled
       \n
       \n     : JUMPER(9) LOC (1^2 2^3) 01"
    
    LINK 
      INIT = JUMPER(9) LOC (1^2 2^3) 01