;
;  SAMSUNG ISA Multifunction Card 
;

BOARD
  ID="SEC0010"
  NAME="SAMSUNG ISA Multifunction Card"
  MFR="SAMSUNG Electronics"
  CATEGORY="MFC"
  SLOT=ISA16
  LENGTH=165
  COMMENTS="The ISA Multifunction Board provides several items like this.
          \n
          \n  - two serial ports
          \n  - a parallel port
          \n  - a floppy disk controller
          \n  - an IDE interface"
  HELP="The ISA Multifunction Board supports manually selectable
        configuration.
      \n  
      \nEach separate function can be enabled or disabled by DIP switch
        and JUMPERs.
      \n  
      \nEach serial port can be selected either as a COM1 or a COM2 by
        DIP switch(SW1-7) and J2.
      \n 
      \nParallel port can be selected as primary or secondary port by
        DIP switch(SW1-6) and J7.
      \n  
      \nFloppy Disk Controller can be selected as a primary or secondary
        port by DIP switch(SW1-1)."
  
SWITCH(1) = 8
  NAME="SW1"
  STYPE=DIP
  REVERSE=YES
  VERTICAL=NO
  FACTORY=LOC(1-8) 11111101
  COMMENTS="SW1 LOC(1)  selects a primary or a secondary port for
          \n            floppy disk controller.
          \nSW1 LOC(2)  enables or disables floppy disk controller.
          \nSW1 LOC(3)  enables or disables COM1 serial port.
          \nSW1 LOC(4)  enables or disables COM2 serial port.
          \nSW1 LOC(5)  enables or disables Parallel port.
          \nSW1 LOC(6)  selects a primary or a secondary parallel port.
          \nSW1 LOC(7)  selects 9 pin D-SUB male connector as COM1 and
          \n            25 pin D-SUB male connector as COM2 or vice versa.
          \nSW1 LOC(8)  enables or disables IDE interface."
  HELP=""
    
JUMPER(2) = 2
  NAME="J2"
  JTYPE=TRIPOLE
  REVERSE=YES      
  VERTICAL=NO
  FACTORY=LOC(1 2) 00
  COMMENTS="This Jumper selects 9 pin D-SUB male connector as COM1 and 25pin
         \nD-SUB male connector as COM2 or vice versa."
  HELP=""

JUMPER(3) = 1
  NAME="J3"
  JTYPE=PAIRED
  VERTICAL=YES
  FACTORY=LOC(1) 1
  COMMENTS="This Jumper is used to disable Floppy Disk Controller.
           \nTo disable Floppy Controller 2nd switch of SW1 should be OFF and
           \nthis jumper should be removed(plug out)."
  HELP=""          

JUMPER(7) = 2
  NAME="J7"
  JTYPE=INLINE
  REVERSE=YES
  VERTICAL=YES
  LABEL=LOC(1^2 2^3)"IRQ5""IRQ7"
  FACTORY=LOC(1^2 2^3) 01      
  COMMENTS="This Jumper is used to select IRQ5 or IRQ7"
  HELP=""

           
FUNCTION = "Floppy Disk Controller"
  TYPE = "MSD"
  COMMENTS = "Floppy Disk Controller can be disabled by setting
               SW1-2 OFF and removing shunt out of J3."
  HELP = "
       \n After modified, user must change the JUMPERs &
       \n SWITCH on the multifunction board."
  
  CHOICE = "Enable Floppy Disk Controller (Primary)"
      HELP = "
         \n JUMPER & SWITCH Setting is like this.
         \n
         \n  a) Enable Floppy Disk Controller (Primary)
         \n
         \n     : JUMPER(3) LOC(1) 1
         \n       SWITCH(1) LOC(2) 1
         \n       SWITCH(1) LOC(1) 1"
    LINK
        IRQ = 6
        DMA = 2
        INIT = JUMPER(3) LOC(1) 1
        INIT = SWITCH(1) LOC(2) 1 
        INIT = SWITCH(1) LOC(1) 1
;
  CHOICE = "Enable Floppy Disk Controller (Secondary)"
    HELP = "
         \n  b) Enable Floppy Disk Controller (Secondary)
         \n
         \n     : JUMPER(3) LOC(1) 1
         \n       SWITCH(1) LOC(2) 1
         \n       SWITCH(1) LOC(1) 0"

    LINK
        IRQ = 6
        DMA = 2
        INIT = JUMPER(3) LOC(1) 1
        INIT = SWITCH(1) LOC(2) 1
        INIT = SWITCH(1) LOC(1) 0
;      
  CHOICE = "Disable Floppy Disk Controller"
    HELP = "
         \n  c) Disable Floppy Disk Controller
         \n
         \n     : JUMPER(3) LOC(1) 0
         \n       SWITCH(1) LOC(2) 0"
    LINK
        INIT = JUMPER(3) LOC(1) 0
        INIT = SWITCH(1) LOC(2) 0
    
FUNCTION = "COM1"
  TYPE="COM,ASY"
  COMMENTS="COM1 can be disabled by setting SW1-3 OFF."
  HELP = "
       \n After modified, user must change the JUMPERs & 
       \n SWITCH on the multifunction board."

  CHOICE = "Enable COM1"
      HELP = "
         \n JUMPER & SWITCH Setting is like this.
         \n
         \n  a) Enable COM1
         \n       
         \n     : SWITCH(1) LOC(3) 1"

    LINK
      IRQ = 4
      INIT = SWITCH(1) LOC(3) 1

  CHOICE = "Disable COM1"
  HELP = "
         \n  b) Disable COM1
         \n
         \n     : JUMPER(2) LOC(1 2) 00
         \n       SWITCH(1) LOC(3) 0"
  
;    DISABLE= yes
;    HELP=""
    
    LINK
 ;     IRQ = 4
      INIT = SWITCH(1) LOC(3) 0
      INIT = JUMPER(2) LOC(1 2) 00    
    
FUNCTION = "COM2"
  TYPE="COM,ASY"
  COMMENTS="COM2 can be disabled by setting SW1-4 OFF."
  HELP = "
       \n After modified, user must change the JUMPERs &
       \n SWITCH on the multifunction board."

  CHOICE = "Enable COM2"
      HELP = "
         \n JUMPER & SWITCH Setting is like this.
         \n
         \n  a) Enable COM2
         \n
         \n     : SWITCH(1) LOC(4) 1"
  
    LINK
      IRQ = 3
      INIT = SWITCH(1) LOC(4) 1

  CHOICE = "Disable COM2"
      HELP = "
         \n  b) Disable COM2
         \n
         \n     : JUMPER(2) LOC(1 2) 00
         \n       SWITCH(1) LOC(4) 0"
  
;    DISABLE= yes
;    HELP=""

    LINK
 ;     IRQ = 3
      INIT = SWITCH(1) LOC(4) 0
      INIT = JUMPER(2) LOC(1 2) 00

    
FUNCTION = "Parallel Port"
  TYPE="PAR"
  COMMENTS="Parallel Port can be disabled by setting SW1-5 OFF."
  HELP = "
       \n After modified, user must change the JUMPERs &
       \n SWITCH on the multifunction board."

  CHOICE = "Enable Parallel Port(LPT1)"
      HELP = "
         \n JUMPER & SWITCH Setting is like this.
         \n
         \n  a) Enable Parallel Port(LPT1)
         \n
         \n     : SWITCH(1) LOC(5) 1
         \n       SWITCH(1) LOC(6) 1
         \n       JUMPER(7) LOC(1^2) 1"

  
    LINK
      IRQ = 7
      INIT = SWITCH(1) LOC(5) 1
      INIT = SWITCH(1) LOC(6) 1
      INIT = JUMPER(7) LOC(2^3) 1

  CHOICE = "Enable Parallel Port(LPT2)"
      HELP = "
         \n  b) Enable Parallel Port(LPT2)
         \n
         \n     : SWITCH(1) LOC(5) 1
         \n       SWITCH(1) LOC(6) 0
         \n       JUMPER(7) LOC(1^2) 1"

    LINK
      IRQ = 5
      INIT = SWITCH(1) LOC(5) 1
      INIT = SWITCH(1) LOC(6) 0
      INIT = JUMPER(7) LOC(1^2) 1

  CHOICE = "Disable Parallel Port"
      HELP = "
         \n  c) Disable Parallel Port
         \n
         \n     : SWITCH(1) LOC(5) 0
         \n       SWITCH(1) LOC(6) 0
         \n       JUMPER(7) LOC(2^3) 1"

;    DISABLE= yes
;    HELP=""
  
    LINK
      INIT = SWITCH(1) LOC(5) 0
      INIT = SWITCH(1) LOC(6) 0
      INIT = JUMPER(7) LOC(2^3) 1
    
FUNCTION = "IDE Interface"                          
  TYPE = "MSD"
  COMMENTS="IDE Interface can be enabled by setting SW1-8 OFF."
  HELP = "
       \n After modified, user must change the JUMPERs &
       \n SWITCH on the multifunction board."
  
  CHOICE = "Disable IDE Interface"
      HELP = "
         \n JUMPER & SWITCH Setting is like this.
         \n
         \n  a) Disable IDE Interface
         \n
         \n     : SWITCH(1) LOC(8) 1"

    LINK
      INIT = SWITCH(1) LOC(8) 1

  CHOICE = "Enable IDE Interface"
      HELP = "
         \n  b) Enable IDE Interface
         \n
         \n     : SWITCH(1) LOC(8) 0"

    LINK
      IRQ = 14  
      INIT = SWITCH(1) LOC(8) 0
      

FUNCTION = "Select COM1 connector"
  TYPE = "COM,ASY"
  COMMENTS = "This is to select 9 pin D-SUB male connector as COM1
              and 25 pin D-SUB male connector as COM2 or vice versa."
  HELP = "
       \n After modified, user must change the JUMPERs &
       \n SWITCH on the multifunction board."

  CHOICE = "Select 9 pin D-SUB male connector as COM1"
      HELP = "
         \n JUMPER & SWITCH Setting is like this.
         \n
         \n  a) Select 9 pin D-SUB male connector as COM1
         \n
         \n     : SWITCH(1) LOC(8) 0
         \n       JUMPER(2) LOC(1 2) 00"
    LINK
      INIT = JUMPER(2) LOC(1 2) 00
      INIT = SWITCH(1) LOC(8) 0

  CHOICE = "Select 25 pin D-SUB male connector as COM1"
      HELP = "
         \n  b) Select 25 pin D-SUB male connector as COM1
         \n
         \n     : SWITCH(1) LOC(7) 1
         \n       JUMPER(2) LOC(1 2) 11"
    LINK
      INIT = JUMPER(2) LOC(1 2) 11
      INIT = SWITCH(1) LOC(7) 1