BOARD
  ID = "RTR8113"
  NAME = "Racore Token-Ring (16/4 Mbps, 16 bit ISA bus)"
  MFR = "Racore Computer Products, Inc."
  CATEGORY = "NET"
  SLOT = ISA16
  READID = NO
  COMMENTS = "\nThis is the Racore 16 bit ISA 16/4Mbps Token Ring network
              \nadapter for ISA and EISA bus compatible computers."

SWITCH(1) = 12
  NAME = "SW1 Config. Switch"
  STYPE = DIP
  VERTICAL = NO
  REVERSE = YES
  LABEL = LOC (1-12) "I/O-SW1" "I/O-SW2" "IRQ-SW3" "IRQ-SW4" "MEM-SW5" "MEM-SW6"
                     "DMA-SW7" "DMA-SW8" "RPL" "SPEED" "DLOAD" "T1/T3"
  COMMENTS = "\nThis is the 12 position configuration DIP switch.
              \nPlease refer to the User Manual for more information."

FUNCTION = "16/4Mbps Token Ring Adapter"
  TYPE = "NET,TOK"

  SUBFUNCTION = "I/O Address Location"
    COMMENTS = "\nRacore supports up to four I/O address selections.
                \nThe preferred I/O address is 0A20h - 0A2Fh."

    CHOICE = "0 = 0A20h - 0A2Fh"
      LINK
        PORT = 0A20h-0A2Fh
          SHARE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(1 2) 01
    CHOICE = "1 = 0A00h - 0A0Fh"
      LINK
        PORT = 0A00h-0A0Fh
          SHARE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(1 2) 11
    CHOICE = "2 = 0A40h - 0A4Fh"
      LINK
        PORT = 0A40h-0A4Fh
          SHARE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(1 2) 10
    CHOICE = "3 = 0A60h - 0A6Fh"
      LINK
        PORT = 0A60h-0A6Fh
          SHARE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(1 2) 00

  SUBFUNCTION = "Interrupt (IRQ) Level"
    TYPE = "INT"
    COMMENTS = "\nRacore supports up to four IRQ level selections.
                \nThe preferred IRQ level is IRQ 2 (9)."

    CHOICE = "Interrupt 2 (9)"
    SUBTYPE = "9"
      LINK
        IRQ = 9
          SHARE = NO
          TRIGGER = EDGE
        INIT = SWITCH(1) LOC(3 4) 01
    CHOICE = "Interrupt 3"
    SUBTYPE = "3"
      LINK
        IRQ = 3
          SHARE = NO
          TRIGGER = EDGE
        INIT = SWITCH(1) LOC(3 4) 11
    CHOICE = "Interrupt 10"
    SUBTYPE = "10"
      LINK
        IRQ = 10
          SHARE = NO
          TRIGGER = EDGE
        INIT = SWITCH(1) LOC(3 4) 10
    CHOICE = "Interrupt 11"
    SUBTYPE = "11"
      LINK
        IRQ = 11
          SHARE = NO
          TRIGGER = EDGE
        INIT = SWITCH(1) LOC(3 4) 00

  SUBFUNCTION = "Memory (ROM) Address Location"
    COMMENTS = "\nRacore support up to four ROM address locations.
                \nThe preferred location is CC000-CFFFF."

    CHOICE = "CC000-CFFFF"
      LINK
        MEMORY = 16K
          ADDRESS = 0CC000h
          WRITABLE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(5 6) 11
    CHOICE = "D0000-D3FFF"
      LINK
        MEMORY = 16K
          ADDRESS = 0D0000h
          WRITABLE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(5 6) 01
    CHOICE = "D8000-DBFFF"
      LINK
        MEMORY = 16K
          ADDRESS = 0D8000h
          WRITABLE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(5 6) 10
    CHOICE = "DC000-DFFFF"
      LINK
        MEMORY = 16K
          ADDRESS = 0DC000h
          WRITABLE = NO
          SIZE = BYTE
        INIT = SWITCH(1) LOC(5 6) 00

  SUBFUNCTION = "DMA Channel Selection"
    TYPE = "DMA"
    COMMENTS = "\nRacore supports up to four DMA channel selections.
                \nThere is no preferred channel selection."

    CHOICE = "DMA Channel 0"
    SUBTYPE = "DMA0"
      LINK
        DMA = 0
          SHARE = NO
          TIMING = DEFAULT
        INIT = SWITCH(1) LOC(7 8) 11
    CHOICE = "DMA Channel 5"
    SUBTYPE = "DMA5"
      LINK
        DMA = 5
          SHARE = NO
          TIMING = DEFAULT
        INIT = SWITCH(1) LOC(7 8) 01
    CHOICE = "DMA Channel 6"
    SUBTYPE = "DMA6"
      LINK
        DMA = 6
          SHARE = NO
          TIMING = DEFAULT
        INIT = SWITCH(1) LOC(7 8) 10
    CHOICE = "DMA Channel 7"
    SUBTYPE = "DMA7"
      LINK
        DMA = 7
          SHARE = NO
          TIMING = DEFAULT
        INIT = SWITCH(1) LOC(7 8) 00

  SUBFUNCTION = "RPL Enable/Disable"
    COMMENTS = "\nIf an RPL EPROM option is installed, you can
                \nenable or disable this funciton with switch #9."

    CHOICE = "RPL Disabled"
      FREE
        INIT = SWITCH(1) LOC(9) 1
    CHOICE = "RPL Enabled"
      FREE
        INIT = SWITCH(1) LOC(9) 0

  SUBFUNCTION = "Adapter Data Rate (Ring Speed)"
    TYPE = "SPD"
    COMMENTS = "\nThe Ring Speed on this adapter is switchable between
                \n4Mbps and 16Mbps. You must set the speed to the same
                \nrate as the LAN segment to which you are connecting."

    CHOICE = "4 Mbps"
    SUBTYPE = "4"
      FREE
        INIT = SWITCH(1) LOC(10) 0
    CHOICE = "16 Mbps"
    SUBTYPE = "16"
      FREE
        INIT = SWITCH(1) LOC(10) 1

  SUBFUNCTION = "ROM or RAM Based MAC/LLC"
    COMMENTS = "\nThe MAC/LLC code executing on the adapter may be ROM or
                \nRAM based. ROM based is preferred but you may select RAM
                \nbased for easy upgrades or optional protocol support."

    CHOICE = "ROM Based"
      FREE
        INIT = SWITCH(1) LOC(11) 1
    CHOICE = "RAM Based"
      FREE
        INIT = SWITCH(1) LOC(11) 0

  SUBFUNCTION = "Type 1 or Type 3 Cable"
    COMMENTS = "\nRacore provides on-board connections to either Type 1
                \n(STP) or Type 3 (UTP) cable. You must select the
                \nappropriate cable, thus enabling the proper connector."

    CHOICE = "Type 1 (STP)"
      FREE
        INIT = SWITCH(1) LOC(12) 1
    CHOICE = "Type 3 (UTP)"
      FREE
        INIT = SWITCH(1) LOC(12) 0