;ษอออออออออออออออออออออออออออออออออออออออออออออออออออออออออออออออออป
;บ                                                                 บ
;บ           Olicom PCA 16/4 Token-Ring Network Adapter            บ
;บ            Adapter Configuration File   Version 1.10            บ
;บ                 Copyright (C) 1992 by Olicom                    บ
;บ                                                                 บ
;ศอออออออออออออออออออออออออออออออออออออออออออออออออออออออออออออออออผ

BOARD
  ID = "OLC0B01"
  NAME = "Olicom PCA 16/4 Token-Ring Network Adapter"
  MFR = "Olicom"
  CATEGORY = "NET"
  SLOT = ISA8
  LENGTH = 109
  AMPERAGE = 800
  SKIRT = NO
  READID = NO
  IOCHECK = INVALID
  DISABLE = UNSUPPORTED

  COMMENTS = "\nThis is the Olicom PCA 16/4 dual-speed
	      (16 Mbps or 4 Mbps) Token Ring Network adapter
	      card for ISA and EISA bus computers.\n\n
	      The configuration utility will select a conflict-free
	      configuration of system resources, and suggest switch
	      settings for the adapter. These should be viewed on
	      exit from the utility and set manually on the card
	      before operation"

SWITCH(1) = 8
  NAME = "SW1 Config. switch"
  STYPE = DIP
  VERTICAL = NO
  REVERSE = YES
  LABEL = LOC(1-8) "SP" "A0" "A1" "I0" "11" "14"
		    "15" "16"
  FACTORY = LOC(1-8) 00000000
  COMMENTS = "This is the 8-position configuration dip-switch.
	      Please refer to the Guide To Operations for an
	      explanation of switch settings."

FUNCTION = "Token-Ring Network Adapter"
  TYPE = "NET,TOK"
  CONNECTION = "9-Pin D-Socket for Token Ring Shielded Twisted
		Pair Lobe Cable or 8-pin Phone-connector for
		Unshielded Twisted Pair Lobe Cable"

  SUBFUNCTION = "I/O Address Location"
    COMMENTS = "\nUp to four Olicom Token-Ring Network adapters
		may be installed in this computer. An adapter must
		use one of four I/O port address combinations.
		Each combination consists of two address ranges.\n
		Use the VIEW SWITCH & JUMPER SETTINGS function
		to display the required switch settings."

    CHOICE = "0 =  0A20 & 0A22-0A23 & 0A30-0A3F"
      LINK
	PORT = 0A20h
	  SHARE = NO
	  SIZE = BYTE
	PORT = 0A22h-0A23h
	  SHARE = NO
	  SIZE = BYTE
	PORT = 0A30h-0A3Fh
	  SHARE = NO
	  SIZE = BYTE
	INIT = SWITCH(1) LOC(2 3) 00
	INIT = PORTADR(0A38h) 11111111
	INIT = PORTADR(0A38h) 00101110
    CHOICE = "1 =  0A24 & 0A26-0A27 & 0A40-0A4F"
      LINK
	PORT = 0A24h
	  SHARE = NO
	  SIZE = BYTE
	PORT = 0A26h-0A27h
	  SHARE = NO
	  SIZE = BYTE
	PORT = 0A40h-0A4Fh
	  SHARE = NO
	  SIZE = BYTE
	INIT = SWITCH(1) LOC(2 3) 01
	INIT = PORTADR(0A48h) 11111111
	INIT = PORTADR(0A48h) 00101110
    CHOICE = "2 =  0A50 & 0A52-0A53 & 0A60-0A6F"
      LINK
	PORT = 0A50h
	  SHARE = NO
	  SIZE = BYTE
	PORT = 0A52h-0A53h
	  SHARE = NO
	  SIZE = BYTE
	PORT = 0A60h-0A6Fh
	  SHARE = NO
	  SIZE = BYTE
	INIT = SWITCH(1) LOC(2 3) 10
	INIT = PORTADR(0A68h) 11111111
	INIT = PORTADR(0A68h) 00101110
    CHOICE = "3 =  0A54 & 0A55-0A57 & 0A70-0A7F"
      LINK
	PORT = 0A54h
	SHARE = NO
	PORT = 0A56h-0A57h
	  SHARE = NO
	  SIZE = BYTE
	PORT = 0A70h-0A7Fh
	  SHARE = NO
	  SIZE = BYTE
	INIT = SWITCH(1) LOC(2 3) 11
	INIT = PORTADR(0A78h) 11111111
	INIT = PORTADR(0A78h) 00101110

  SUBFUNCTION = "Adapter Data Rate"
    TYPE = "SP"
    COMMENTS = "\nThis Token-Ring Network adapter can operate
		at two different data rates, 4 Mbps or 16 Mbps.
		You MUST set the adapter data rate to the same
		rate as the Token-Ring Network LAN segment to
		which you are connecting the adapter.\n
		Use the VIEW SWITCH & JUMPER SETTINGS function
		to display the required switch setting."

    CHOICE = "4 Mbps"
    SUBTYPE = "4"
      FREE
	INIT = SWITCH(1) LOC(1) 0
    CHOICE = "16 Mbps" 
    SUBTYPE = "16"
      FREE
	INIT = SWITCH(1) LOC(1) 1

  SUBFUNCTION = "RPL EPROM Address Location"
    COMMENTS = "\nThere are 7 possible 8K blocks of PC memory
		for the RPL EPROM area. The Preferred address
		location is: CE000-CFFFF.\n
		Use the VIEW SWITCH & JUMPER SETTINGS function
		to display the required switch settings."

    CHOICE = "EPROM Disabled"
      LINK
	INIT = SWITCH(1) LOC(6-8) 000
    CHOICE = "C6000-C7FFF"
      LINK
	MEMORY = 8K
	  ADDRESS = 0C6000h
	  WRITABLE = NO
	  SIZE = BYTE
	INIT = SWITCH(1) LOC(6-8) 100
    CHOICE = "CA000-CBFFF"
      LINK
	MEMORY = 8K
	  ADDRESS = 0CA000h
	  WRITABLE = NO
	  SIZE = BYTE
	INIT = SWITCH(1) LOC(6-8) 010
    CHOICE = "CE000-CFFFF"
      LINK
	MEMORY = 8K
	  ADDRESS = 0CE000h
	  WRITABLE = NO
	  SIZE = BYTE
	INIT = SWITCH(1) LOC(6-8) 110
    CHOICE = "D2000-D3FFF"
      LINK
	MEMORY = 8K
	  ADDRESS = 0D2000h
	  WRITABLE = NO
	  SIZE = BYTE
	INIT = SWITCH(1) LOC(6-8) 001
    CHOICE = "D6000-D7FFF"
      LINK
	MEMORY = 8K
	  ADDRESS = 0D6000h
	  WRITABLE = NO
	  SIZE = BYTE
	INIT = SWITCH(1) LOC(6-8) 101
    CHOICE = "DA000-DBFFF"
      LINK
	MEMORY = 8K
	  ADDRESS = 0DA000h
	  WRITABLE = NO
	  SIZE = BYTE
	INIT = SWITCH(1) LOC(6-8) 011
    CHOICE = "DE000-DFFFF"
      LINK
	MEMORY = 8K
	  ADDRESS = 0DE000h
	  WRITABLE = NO
	  SIZE = BYTE
	INIT = SWITCH(1) LOC(6-8) 111

  SUBFUNCTION = "Interrupt Level"
    TYPE = "INT"
    COMMENTS = "\nThis Token-Ring Network adapter can operate
		on one of four interrupt levels: 2 (9), 3, 5,
		or 7. The preferred interrupt level is 2 (9).\n
		NOTE that the adapter only uses edge-triggered
		interrupts.\n
		Use the VIEW SWITCH & JUMPER SETTINGS function
		to display the required switch settings."

    CHOICE = "Interrupt 2 (9)"
    SUBTYPE = "9"
      LINK
	IRQ = 9
	  SHARE = NO
	  TRIGGER = EDGE
	INIT = SWITCH(1) LOC(4 5) 00
    CHOICE = "Interrupt 3"
    SUBTYPE = "3"
      LINK
	IRQ = 3
	  SHARE = NO
	  TRIGGER = EDGE
	INIT = SWITCH(1) LOC(4 5) 10
    CHOICE = "Interrupt 5"
    SUBTYPE = "5"
      LINK
	IRQ = 5
	  SHARE = NO
	  TRIGGER = EDGE
	INIT = SWITCH(1) LOC(4 5) 01
    CHOICE = "Interrupt 7"
    SUBTYPE = "7"
      LINK
	IRQ = 7
	  SHARE = NO
	  TRIGGER = EDGE
	INIT = SWITCH(1) LOC(4 5) 11