;
;Newport Systems Solutions WNIC Adapter
;EISA Configuration File
;Last update: 01/21/93
;
BOARD
   ID = "NSS0011"
   NAME = "Newport Systems Solutions WNIC Adapter"
   MFR = "Newport Systems Solutions"
   CATEGORY = "NET"
   SLOT = ISA16
   LENGTH = 337
   SIZING = 64K
   COMMENTS = "
The WNIC (Wide-area Network Interface Coprocessor) adapter provides
two or four synchronous I/O ports for communications with remote LANs
and workstations. It may optionally be equipped with a Data Compres-
sion Module (DCM) daughter-board."
   HELP = "
To setup the WNIC adapter for proper operation within the EISA environment,
you must configure a valid I/O Port Address, Memory Window, and Interrupt
(IRQ). Upon completing the configuration, be sure to note the WNIC
parameters that you have selected. You will need them later when you go to
load and/or configure the software that will be using the WNIC adapter."
;-------------------------------------------------------------------------
SWITCH(1) = 3
   NAME = "SW1"
   STYPE = DIP
   REVERSE = YES
   FACTORY = LOC(1-3) 111

;-------------------------------------------------------------------------
FUNCTION = "WNIC Port Address Selection"
   HELP = "
Select a range of I/O ports for the WNIC adapter to use. Your choice here
must correspond with how the dip-switch bank 'SW1' has been physically set
on the WNIC adapter. The factory default setting is 258h-25Fh (all three
switches set to the ON position)."
   CHOICE = "I/O Port Addresses"
      LINK
         PORT = 258h-25Fh | 268h-26Fh | 298h-29Fh | 2D8h-2DFh |
                358h-35Fh | 398h-39Fh | 3E8h-3EFh
         SHARE = NO
         SIZE = WORD
         INIT = SWITCH(1) LOC(1-3) 111 | 011 | 101 | 001 | 110 | 010 | 100

;-------------------------------------------------------------------------
FUNCTION = "WNIC Memory Window Selection"
   HELP = "
First, specify whether you are installing a Rev. D WNIC adapter or a Rev. E,
and whether you wish to configure a Low or High-memory address. Second, you
may edit resources to select the specific memory address for the WNIC to
use."
   CHOICE = "Rev. D WNIC, Low-memory"
      LINK
         MEMORY = 64K
         ADDRESS = 0A0000h | 0D0000h
         WRITABLE = YES
         MEMTYPE = OTHER
         SIZE = WORD
         DECODE = 24
         CACHE = NO
         SHARE = "NSS0011"

   CHOICE = "Rev. D WNIC, High-memory"
      LINK
         MEMORY = 512K
         ADDRESS = 0980000h | 0A00000h | 0A80000h | 0B00000h | 0B80000h |
                   0C00000h | 0C80000h
         WRITABLE = YES
         MEMTYPE = OTHER
         SIZE = WORD
         DECODE = 24
         CACHE = NO
         SHARE = "NSS0011"

   CHOICE = "Rev. E WNIC, Low-memory"
      LINK
         MEMORY = 64K
         ADDRESS = 0A0000h | 0C0000h | 0D0000h | 0E0000h
         WRITABLE = YES
         MEMTYPE = OTHER
         SIZE = WORD
         DECODE = 24
         CACHE = NO
         SHARE = "NSS0011"

   CHOICE = "Rev. E WNIC, High-memory"
      LINK
         MEMORY = 512K
         ADDRESS = 0B80000h | 0C00000h | 0C80000h | 0D80000h | 0E00000h |
                   0E80000h | 0F00000h
         WRITABLE = YES
         MEMTYPE = OTHER
         SIZE = WORD
         DECODE = 24
         CACHE = NO
         SHARE = "NSS0011"

;-------------------------------------------------------------------------
FUNCTION = "WNIC IRQ Selection"
   HELP = "
Select which Interrupt (IRQ) you would like the WNIC adapter to use."
   CHOICE = "IRQ Lines"
      LINK
         IRQ = 3 | 4 | 5 | 9 | 10 | 11 | 12 | 15
         SHARE = NO
         TRIGGER = EDGE