BOARD
  ID = "NIC1100"
  NAME = "AT-DSP2200 DSP Accelerator/Audio I/O Board"
  MFR = "NATIONAL INSTR CORP"
  CATEGORY = "OTH"
  SLOT = ISA16
  READID = NO
  COMMENTS = "This AT-DSP2200 by National Instruments is a high-performance DSP
         accelerator board with high-accuracy audio frequency (DC to 20kHz)
         analog input/output."

SWITCH(1) = 5
   NAME = "Base I/O Address"
   STYPE = DIP
   VERTICAL = NO
   REVERSE = YES
   LABEL = LOC(1-5) "A9" "A8" "A7" "A6" "A5"
   FACTORY = LOC(1-5) 01001
   COMMENTS = "The base I/O address is determined by the settings of the
         board dip switches.  The factory setting is for base address 0140h."

FUNCTION = "AT-DSP2200 Base I/O Address"
   COMMENTS = "The base I/O address selected through this resource."
	HELP = "The base I/O address entered here must match the board 
		dip switch setting for the base address. See the user's 
		manual of the board for more information."
	CHOICE = "Base I/O address Resource"
		SUBCHOICE
		FREE
			PORT = 120h-3FFh STEP = 020h
			SHARE = NO
			INIT = SWITCH(1) LOC(1-5) 01001 | 01010 | 01011 |
                                01100 | 01101 | 01110 | 01111 | 10000 |
                                                10001 | 10010 | 10011 |
				10100 | 10101 | 10110 | 10111 | 11000 |
				11001 | 11010 | 11011 | 11100 | 11101 |
				11110 | 11111
		SUBCHOICE
		FREE
			PORT = 000h-120h STEP = 020h
			SHARE = NO
			INIT = SWITCH(1) LOC(1-5) 00000 | 00001 | 00010 |
				00011 | 00100 | 00101 | 00110 | 00111 |
				01000

FUNCTION = "AT-DSP2200 DMA Channel"
 	COMMENTS = "The DMA channel to be used is selected through this
		    function. \n\nIf you select the Disabled option, the driver
		    will not perform DMA transfers through the board.  However,
		    if you select the Disabled option, you must also set the
		    Data Acquisition mode to Programmed Input/Output for the
		    driver to perform Data Acquisition functions on the board."
;SHARE statement in the choices is omitted as default is NO
  	CHOICE = "0"
        FREE
                DMA = 0
                SIZE = WORD
                TIMING = DEFAULT

        CHOICE = "1"
        FREE
                DMA = 1
                SIZE = WORD
                TIMING = DEFAULT

        CHOICE = "2"
        FREE
                DMA = 2
                SIZE = WORD
                TIMING = DEFAULT

        CHOICE = "3"
        FREE
                DMA = 3
                SIZE = WORD
                TIMING = DEFAULT

        CHOICE = "5"
        FREE
                DMA = 5
                SIZE = WORD
                TIMING = DEFAULT

        CHOICE = "6"
        FREE
                DMA = 6
                SIZE = WORD
                TIMING = DEFAULT

        CHOICE = "7"
        FREE
                DMA = 7
                SIZE = WORD
                TIMING = DEFAULT

FUNCTION = "AT-DSP2200 Interrupt Request Level"
	COMMENTS = "The interrupt level is selected through this function."
;SHARE statement in the choices is omitted as default is NO
;TRIGGER statement in the choices is omitted as default is EDGE
;   The default values assigned for SHARE and TRIGGER are being ignored.

	CHOICE = "9"
        FREE
		IRQ = 9	

	CHOICE = "10"
        FREE
		IRQ = 10

	CHOICE = "11"
        FREE
		IRQ = 11

	CHOICE = "12"
        FREE
		IRQ = 12

	CHOICE = "14"
        FREE
		IRQ = 14

	CHOICE = "15"
        FREE
		IRQ = 15

	CHOICE = "3"
        FREE
		IRQ = 3 

	CHOICE = "4"
        FREE
		IRQ = 4

	CHOICE = "5"
        FREE
		IRQ = 5

	CHOICE = "6"
        FREE
		IRQ = 6

	CHOICE = "7"
        FREE
		IRQ = 7