;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; ; NEC System config file for MIPS processor R96B ; ; !NEC2E01.CFG for NEC RISCserver 2250 (R96B) ; ; ; Rev 1.0 1995-08/18 ??:??:?? T.Y. ; Ordinal file NEC1C01.CFG for R96 ; ; Ver.1.00.05 : 9/19/95 : R94D & R96B added to ECU disk : CG,NECTECH; ; CHOICE="Version 1.00.05" ; ; Ver.1.00.06 : 10/31/95: Fixed # of PCI SLOTS in ECU file: CG,NECTECH; ; CHOICE="Version 1.00.06" ; ; Ver.1.00.07 : 3/19/96 : No change from .06 : RR,NECTECH; ; ; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; BOARD ID="NEC2E01" NAME="NEC MIPS System Board" MFR="NEC" CATEGORY="SYS" SLOT=EMB(0) READID=NO SIZING=0 COMMENTS="The NEC NEC RISCserver 2250 contains dual MIPS R4400 RISC processors, 6 EISA slots and 3 PCI slots" HELP="This is the Board Identification Block help field for the NEC RISCserver 2250 System board." SYSTEM NONVOLATILE=7680 AMPERAGE=31500 SLOT(1)=EISA(1) LENGTH=341 SKIRT=YES BUSMASTER=YES SLOT(2)=EISA(2) LENGTH=341 SKIRT=YES BUSMASTER=YES SLOT(3)=EISA(3) LENGTH=341 SKIRT=YES BUSMASTER=YES SLOT(4)=EISA(4) LENGTH=341 SKIRT=YES BUSMASTER=YES SLOT(5)=EISA(5) LENGTH=341 SKIRT=YES BUSMASTER=YES SLOT(6)=EISA(6) LENGTH=341 SKIRT=YES BUSMASTER=YES JUMPER(1) = 2 NAME = "J17" JTYPE = PAIRED VERTICAL = NO REVERSE = NO LABEL = LOC(1-2) "Jy" "Jx" INITVAL = LOC(1-2) 10 COMMENTS = "Jumpers Jx and Jy select the type of power on/off control.\n \nJx enabled & Jy disabled = Power on/off controlled through hardware\n \nJx disabled & Jy enabled = Power on/off controlled through softWare." HELP = " The jumper switch is located on the system board in position J17." JUMPER(2) = 1 NAME = "J51" JTYPE = PAIRED VERTICAL = YES REVERSE = NO LABEL = LOC(1) "Jz" INITVAL = LOC(1) 0 COMMENTS = "Jumper Jz selects the memory type used in the system.\n \nJz enabled = System uses EDO DRAM.\n \nJz disabled = System uses normal DRAM." HELP = "The memory type jumper is located on the system board in position J51." FUNCTION="DummySystemType" SHOW=NO COMMENTS="Fools s/w into put header at top of file" HELP="None" CHOICE="Dummy" ;;Special function for MIPS boards , this is described in the ARC Specification ;; addendum, rev 1.1. FUNCTION = "*Component* Entry!" SHOW = NO TYPE = "CE = other,0" CHOICE = "" FUNCTION="VidMem" TYPE="MEM" SHOW=NO CHOICE="OK" FREE MEMORY=1M ADDRESS=0E00000h WRITABLE=NO MEMTYPE=OTH FUNCTION = "EISANoMapAddress" TYPE = "MEM" SHOW = NO CHOICE = "OK" FREE MEMORY = 3M ADDRESS = 100000h WRITABLE = YES MEMTYPE = VIR FUNCTION="NEC2E01.CFG Version" CHOICE="1.00.07"