;******************************************************************************
;*                                                                            *
;*  Madge Blue+ 16/4 ISA Token Ring Adapter                                   *
;*      Adapter Configuration File  Version 1.0                               *
;*          Copyright (C) 1994 Madge Networks                                 *
;*                                                                            *
;******************************************************************************

BOARD
  ID            = "MDG2000"
  NAME          = "Madge Blue+ 16/4 ISA Token Ring Adapter"
  MFR           = "Madge Networks Ltd."
  CATEGORY      = "NET"
  SLOT          = ISA16
  LENGTH        = 213
  AMPERAGE      = 1000
  SKIRT         = NO
  READID        = NO
  IOCHECK       = INVALID
  DISABLE       = UNSUPPORTED

  COMMENTS      = "The Madge Blue+ 16/4 ISA Token Ring Network Adapter may 
		   be used in ISA and EISA bus computers. \n\n
		   The EISA configuration utility supplied with your EISA bus
		   computer will identify a conflict free configuration of
		   system resources and suggest switch settings for this 
		   adapter. Before exiting the configuration utility, 
		   record the suggested switch settings, then exit and
		   set switches manually on the adapter before continuing.\n\n
		   NOTE: Switch setting changes only take effect following a
		   power ON/OFF cycle."


SWITCH(1)       = 12
  NAME          = "SW1 Configuration"
  STYPE         = DIP
  VERTICAL      = YES
  REVERSE       = YES
  INITVAL       = LOC (1-12) xxxxxxxxxxxx
  FACTORY       = LOC (1-12) 011001110010
  COMMENTS      = "Switch block SW1 is a 12-position configuration DIP-switch
		   used to set the ROM address, interrupt level, primary or
		   alternate adapter, the shared RAM size, and the ring
		   speed. "


SWITCH(2)       = 3
  NAME          = "SW2 Configuration Switch"
  STYPE         = DIP
  VERTICAL      = YES
  REVERSE       = YES
  INITVAL       = LOC (1-3) xxx
  FACTORY       = LOC (1-3) 011
  COMMENTS      = "Switch block SW2 is a 3-position configuration DIP-switch
		   used to set 8 or 16 bit mode, enable/disable the remote
		   boot ROM, and set bus timings."


FUNCTION        = "Madge Blue+ 16/4 ISA adapter"
  TYPE          = "NET,TOK"
  CONNECTION    = "9-pin, D-socket: Token Ring lobe cable"


  SUBFUNCTION   = "Alternate/Primary Adapter"
    COMMENTS    = "Up to two Madge Blue+ 16/4 ISA Token Ring Network
		   Adapters may be installed within a single computer. With 
		   multiple adapters installed, one adapter MUST be designated
		   as the primary adapter, with the other set as the alternate
		   adapter. If only one adapter is installed, it should be 
		   set to be a primary adapter. The factory default setting
		   is primary adapter."

    CHOICE      = "Primary"
     FREE
       PORT             = 0a20h-0a23h
	SHARE   = NO
       PORT             = 0a28h-0a2bh
	SHARE   = NO
       PORT             = 0a30h-0a33h
	SHARE   = NO
       PORT             = 0a38h-0a3bh
	SHARE   = NO
	  INIT          = SWITCH(1) LOC(9) 0

    CHOICE      = "Alternate"
      FREE
	PORT    = 0a24h-0a27h
	  SHARE = NO
	PORT    = 0a2ch-0a2fh
	  SHARE = NO
	PORT    = 0a34h-0a37h
	  SHARE = NO
	PORT    = 0a3ch-0a3fh
	  SHARE = NO
      INIT      = SWITCH(1) LOC(9) 1


  SUBFUNCTION   = "Adapter Ring Speed"
    COMMENTS    = "The Madge Blue+ 16/4 ISA Token Ring Network Adapter can 
    		   operate at either 4 or 16 Mbps ring speed.
		   The adapter ring speed MUST match that of the network
		   it is connected to. The factory default setting is
		   16 Mbps."

    CHOICE      = "16 Mbps"
    FREE
      INIT          = SWITCH(1) LOC(12) 0

    CHOICE          = " 4 Mbps"
    FREE
      INIT          = SWITCH(1) LOC(12) 1


  SUBFUNCTION   = "ROM Address Location"
    COMMENTS    = "The factory default ROM address location for the adapter
		   is CC000-CDFFF."

    CHOICE      = "CC000-CDFFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0cc000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 011001b

    CHOICE      = "CE000-CFFFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0ce000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 011000b

    CHOICE      = "D0000-D1FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0d0000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 010111b

    CHOICE      = "D2000-D3FFF"
    LINK        
     MEMORY     = 8K
	ADDRESS = 0d2000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 010110b

    CHOICE      = "D4000-D5FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0d4000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 010101b

    CHOICE      = "D6000-D7FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0d6000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 010100b

    CHOICE      = "D8000-D9FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0d8000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 010011b

    CHOICE      = "DA000-DBFFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0da000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 010010b

    CHOICE      = "DC000-DDFFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0dc000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 010001b

    CHOICE      = "DE000-DFFFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0de000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 010000b


    CHOICE      = "C0000-C1FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0c0000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 011111b

    CHOICE      = "C2000-C3FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0c2000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 011110b

    CHOICE      = "C4000-C5FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0c4000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 011101b

    CHOICE      = "C6000-C7FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0c6000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 011100b

    CHOICE      = "C8000-C9FFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0c8000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 011011b

    CHOICE      = "CA000-CBFFF"
    LINK
      MEMORY    = 8K
	ADDRESS = 0cA000h
	WRITABLE= NO
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC(1-6) 011010b

  SUBFUNCTION   = "Interrupt Level"
    COMMENTS    = "The Madge Blue+ 16/4 ISA Token Ring Network Adapter can 
    		   operate on one of four interrupt levels in IBM-compatible
    		   mode: 2(9), 3, 6 and 7. In addition, if you are going to
    		   use Blue+ drivers you can set the card to interrupt levels
    		   10, 11, 12 and 15.  NOTE: Interrupt level 6 is used by the
    		   disk drive. If you have a disk drive present do not set your
    		   adapter card to  level 6 so as to avoid resource conflicts.
    		   The factory default setting is Interrupt 2(9)."

    CHOICE      = "Interrupt 2 (9)"
    LINK 
      IRQ       = 9
	SHARE   = NO
	TRIGGER = EDGE
      INIT      = SWITCH(1) LOC(7-8) 11b
      

    CHOICE      = "Interrupt 3"
    LINK 
      IRQ       = 3
	SHARE   = NO
	TRIGGER = EDGE
      INIT      = SWITCH(1) LOC(7-8) 10b

    CHOICE      = "Interrupt 6"
    LINK 
      IRQ       = 6
	SHARE   = NO
	TRIGGER = EDGE
      INIT      = SWITCH(1) LOC(7-8) 01b

    CHOICE      = "Interrupt 7"
    LINK 
      IRQ       = 7
	SHARE   = NO
	TRIGGER = EDGE
      INIT      = SWITCH(1) LOC(7-8) 00b

    CHOICE      = "Interrupt 10 (Blue+ drivers only)"
    LINK 
      IRQ       = 10
	SHARE   = NO
	TRIGGER = EDGE
      INIT      = SWITCH(1) LOC(7-8) 11b

    CHOICE      = "Interrupt 11 (Blue+ drivers only)"
    LINK 
      IRQ       = 11
	SHARE   = NO
	TRIGGER = EDGE
      INIT      = SWITCH(1) LOC(7-8) 11b

    CHOICE      = "Interrupt 12 (Blue+ drivers only)"
    LINK 
      IRQ       = 12
	SHARE   = NO
	TRIGGER = EDGE
      INIT      = SWITCH(1) LOC(7-8) 11b

    CHOICE      = "Interrupt 15 (Blue+ drivers only)"
    LINK 
      IRQ       = 15
	SHARE   = NO
	TRIGGER = EDGE
      INIT      = SWITCH(1) LOC(7-8) 11b


  SUBFUNCTION   = "Shared RAM Size/Location"
    COMMENTS    = "The factory default RAM size is 16KB, and the 
		   default shared RAM address is D8000. To change the 
		   shared RAM address, use the Edit/Change Resource option."

    CHOICE      = "16 KB"
    FREE
      MEMORY    = 16k
	ADDRESS = 0d8000h | 0dc000h |
		  0c0000h | 0c4000h | 0c8000h | 0cc000h    |
		  0d0000h | 0d4000h 
	WRITABLE= YES
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC (10-11) 01b | 01b | 01b | 01b |
					01b | 01b | 01b | 01b 

    CHOICE      = "None (Blue+ drivers - FastBlue mode only)"
    FREE
    INIT        = SWITCH(1) LOC (10-11) 01b

    CHOICE      = "8  KB"
    FREE
      MEMORY    =  8k
	ADDRESS = 0d8000h | 0da000h | 0dc000h | 0de000h |
		  0c0000h | 0c2000h | 0c4000h | 0c6000h | 
		  0c8000h | 0ca000h | 0cc000h | 0ce000h |
		  0d0000h | 0d2000h | 0d4000h | 0d6000h 
		  
	WRITABLE= YES
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC (10-11) 11b | 11b | 11b | 11b |
					11b | 11b | 11b | 11b |
					11b | 11b | 11b | 11b |
					11b | 11b | 11b | 11b 

    CHOICE        = "32 KB"
    FREE
      MEMORY    = 32k
	ADDRESS = 0d0000h | 0d8000h | 0c0000h | 0c8000h 
	WRITABLE= YES
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC (10-11) 10b | 10b | 10b | 10b

    CHOICE      = "64 KB"
    FREE
      MEMORY    = 64k
	ADDRESS = 0d0000h | 0c0000h
	WRITABLE= YES
	MEMTYPE = OTH
	SIZE    = BYTE
	DECODE  = 20
	CACHE   = NO
	SHARE   = NO
      INIT      = SWITCH(1) LOC (10-11) 00b | 00b


  SUBFUNCTION   = "Full 128K addressing Mode"
    COMMENTS    = "On most PCs you will NOT need to select this option.
		   On a few PCs however you will need to select Full 128K 
		   addressing mode because the top 3 bits of an address being
		   ready does not imply that the rest of the bits of the 
		   address are valid.\n\nIf you DO have a PC requiring Full
		   128k addressing, but do not set this option ON, then you
		   may get corrupt data or the Blue+ card may not be able to
		   initialise."

    CHOICE      = "Disabled"
      FREE
      INIT      = SWITCH(2) LOC (1) 0

    CHOICE      = "Enabled"
      FREE
      INIT      = SWITCH(2) LOC (1) 1


  SUBFUNCTION   = "8/16 Bit Mode"
    COMMENTS    = "The Madge Blue+ 16/4 ISA Token Ring Network Adapter can 
    		   perform either 8 bit or 16 bit data transfers. In 16 bit 
    		   mode the adapter senses the slot size. In 8 bit mode the 
    		   adapter is forced to use only 8-bit transfers. The factory 
    		   default setting is 16 bit mode."

    CHOICE      = "16 Bit Mode"
      FREE
      INIT      = SWITCH(2) LOC (2) 1

    CHOICE      = "8  Bit Mode"
      FREE
      INIT      = SWITCH(2) LOC (2) 0


  SUBFUNCTION   = "Remote Boot ROM"
    COMMENTS    = "The Madge Blue+ 16/4 ISA Token Ring Network adapter is
                   fitted with a remote boot ROM which enables the PC to
                   remote boot off a server. The ROM may either be enabled or
                   disabled. The factory default setting is enabled."

    CHOICE      = "Enabled"
      FREE
      INIT      = SWITCH(2) LOC (3) 1

    CHOICE      = "Disabled"
      FREE
      INIT      = SWITCH(2) LOC (3) 0