; LongShine LCS-8734 EISA 32-Bit SONIC Network Controller
; PC Fab. Rev. 1
;
; (C)Copyright PLX Technology, 1991
;    All Rights Reserved.
;
; (C)Copyright LONGSHINE Electronices Crop, 1992
;    All Rights Reserved.
;
; 05/22/91 v1.1

BOARD
   ID = "LCS1001"               ; EISA 9010DEMO Rev 1 Product ID.
   NAME = "LCS-8734 EISA 32-Bit Ethernet Controller"
   MFR = "LONGSHINE"            ; Manufacturere Name.
   CATEGORY = "NET"             ; Category, i.e. Network Board.
   SLOT = EISA			; Uses EISA Slot.
   LENGTH = 216 		; Length of Board in Millimeters.
   READID = yes 		; Board ID can be read
   BUSMASTER = 23		; Bus latency time allowed
   AMPERAGE = 1000		; Needs to be measured.
   IOCHECK = INVALID		; Card will not respond to reads of
				;  it's IOCHKERR bit.
   DISABLE = SUPPORTED		; The card can be disabled by clearing
				;  the control register ENABLE bit.
   COMMENTS = " The LCS-8734 Board is a 32 bit SONIC Ethernet Adaptor
		for the EISA bus.  The board is a bus master design
		that uses the host system main memory directly.
		When receiving or transmitting packet data or during
		buffer management, the SONIC requests the bus from the
		host system.  "

   HELP = "No help available."

IOPORT(1) = 0zc88h
   INITVAL = 01xxxxxx		;slave size=16, master size=32

IOPORT(2) = 0zc89h

IOPORT(3) = 0zc8Ah

IOPORT(4) = 0zc8Fh


JUMPER(1) = 1
   NAME = "Thin/Thick NET"
   JTYPE = TRIPOLE
   VERTICAL = NO
   REVERSE = NO
   LABEL = LOC(1) "E1"
   COMMENTS = "Upper Position = Thin net enabled when User Bit 1 is high.\n
				Thick net enabled when User Bit 1 is low.\n
	       Lower Position = Thin net always enabled."


SOFTWARE(1) =
"The LCS-8734 Board can be tested with the FTP8734 Exectuter
Program called eisonic.exe.  A Novell driver allows the
board to be used in a server or workstation. And NDIS Drivers
for LAN Mangement."

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

FUNCTION = "LCS-8734 Ethernet I/O Addresses"
   COMMENTS = "This board supports both slot-specific and ISA\n
		compatible I/O addressing.  The ISA mode should only\n
		be used for software compatibility with ISA drivers."

      CHOICE = "Slot-Specific Only (Default)"
	FREE
	INIT = IOPORT(2) LOC(7-4) 0000

      CHOICE = "Slot-Specific and ISA"
	LINK
	INIT = IOPORT(2) LOC(7-4) 0001|0010|0101|0111|1001|1011|1101
	PORT = 100h-11Fh|120h-13fh|140h-15fh|160h-17fh|300h-31fh|
	       320h-32fh|340h-35fh


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

FUNCTION = "LCS-8734 Ethernet EPROM"
      CHOICE = "EPROM Disabled (Default)"
	FREE
	INIT = IOPORT(3) LOC(7-6) 00

      CHOICE = "27256 (32K x 8)"
	LINK
	MEMORY = 32K
	ADDRESS = 0C0000H-0D8000H step=32K
	WRITABLE = NO
	MEMTYPE = OTHER
	SIZE = BYTE
	DECODE = 24
	CACHE = YES
	FREE
	INIT = IOPORT(2) LOC(5-4) 00 | 01 | 10 | 11
	INIT = IOPORT(3) LOC(7-6) 11


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

FUNCTION = "Bus Master"

   SUBFUNCTION = "Bus Release After Preempt"
      CHOICE = "23 BCLK Cycles"
	FREE
	INIT = IOPORT(1) LOC(5) 0

      CHOICE = "55 BCLK Cycles"
	FREE
	INIT = IOPORT(1) LOC(5) 1


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

FUNCTION = "LCS-8734 Ethernet Interrupt"

   SUBFUNCTION = "Interrupter Choice "
      CHOICE = "IRQ 5"
	FREE
	INIT = IOPORT(1) LOC(2-0) 001

      CHOICE = "IRQ 9"
	FREE
	INIT = IOPORT(1) LOC(2-0) 011

      CHOICE = "IRQ 10"
	FREE
	INIT = IOPORT(1) LOC(2-0) 101

      CHOICE = "IRQ 11"
	FREE
	INIT = IOPORT(1) LOC(2-0) 111

;;;   SUBFUNCTION = "Interrupt Edge/Level"
;;;	 CHOICE = "Edge Triggered Interrupt"
;;;	 LINK
;;;	   IRQ = 9|10|11|5
;;;	    TRIGGER = EDGE
;;;	    SHARE = NO
;;;	   INIT = IOPORT(1) LOC(2-0) 011|101|111|001
;;;
;;;	 CHOICE = "Level Triggered Interrupt"
;;;	 LINK
;;;	   IRQ = 9|10|11|5
;;;	    TRIGGER = LEVEL
;;;	    SHARE = NO
;;;	   INIT = IOPORT(1) LOC(2-0) 010|100|110|000
;;;
;;;   SUBFUNCTION = "Interrupt Latch"
;;;	 CHOICE = "Unlatched"
;;;	   FREE
;;;	   INIT = IOPORT(1) LOC(3) 0
;;;
;;;	 CHOICE = "Latched"
;;;	   FREE
;;;	   INIT = IOPORT(1) LOC(3) 1
;;;

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

FUNCTION = "Ethernet"
   CONNECTION = "J5 (AUI, 15 pin D); J6 (Thinnet, BNC)"
   SUBFUNCTION = "Packet Reception"
      CHOICE = "Receive Own Packets"
	FREE
	INIT = IOPORT(2) LOC(0) 1

      CHOICE = "Don't Receive Own Packets"
	FREE
	INIT = IOPORT(2) LOC(0) 0

   SUBFUNCTION = "Thin/Thick Selection"
   COMMENTS = "The selection between J5 and J6 is made with\n
		jumper E1 in conjunction with User Bit 1."

      CHOICE = "Thin Ethernet (Jumper Selected)"
	LINK
	INIT = JUMPER(1) LOC(1) 1

      CHOICE = "Think Ethernet (Jumper Selected)"
	FREE
	INIT = JUMPER(1) LOC(1) 0


   SUBFUNCTION = "Twisted-Pair Normal/Extend line length"
   COMMENTS = "The selection TP sequeich thresholds have been
	       lowered for use with longer line length, or the standard
	       10BaseT values."

      CHOICE = "AT&T 7220A Support longer length"
	LINK
	INIT = IOPORT(2) LOC(3) 1

      CHOICE = "AT&T 7220A Support normal length"
	LINK
	INIT = IOPORT(2) LOC(3) 0