BOARD
   ID       = "ISAAD00"
   NAME     = "TOPS FlashCard"
   MFR      = "TOPS/Sun Microsystems"
   CATEGORY = "COM"
   SLOT     = ISA8
   LENGTH   = 165
   COMMENTS = "
 The FlashCard for the PC acts as an interface
 between an IBM PC or compatible and an AppleTalk
 network.\n\n
 The PC-FlashCard is designed to be easily installed
 in any slot of a PC, XT (except for slot 8), AT or
 compatible."
   HELP     = "
 If you experience intermittent loss of data or transmissions
 on the network, you should double-check all the network
 connections as well as the network configuration."

JUMPER(1) = 2
   NAME     = "Ja1"
   JTYPE    = INLINE
   VERTICAL = YES
   LABEL    = LOC(3^2 2^1) "H" "L"
   FACTORY  = LOC(3^2 2^1) 10
   COMMENTS = "
 This jumper, along with Ja2 and Ja3, is used
 to set the board I/O address.\n\n
 I/O address:\t    Ja1:\n
 \t    398\t H\n
 \t    390\t H\n
 \t    310\t L\n"

JUMPER(2) = 2
   NAME     = "Ja2"
   JTYPE    = INLINE
   LABEL    = LOC(3^2 2^1) "L" "H"
   FACTORY  = LOC(3^2 2^1) 10
   COMMENTS = "
 This jumper, along with Ja1 and Ja3, is used
 to set the board I/O address.\n\n
 I/O address:\t    Ja2:\n
 \t    398\t\t L\n
 \t    390\t\t L\n
 \t    310\t\t L\n"

JUMPER(3) = 2
   NAME     = "Ja3"
   JTYPE    = INLINE
   LABEL    = LOC(3^2 2^1) "L" "H"
   FACTORY  = LOC(3^2 2^1) 01
   COMMENTS = "
 This jumper, along with Ja1 and Ja2, is used
 to set the board I/O address.\n\n
 I/O address:\t    Ja3:\n
 \t    398\t\t H\n
 \t    390\t\t L\n
 \t    310\t\t L\n"

JUMPER(4) = 2
   NAME     = "Jint"
   JTYPE    = INLINE
   LABEL    = LOC(3^2 2^1) "3" "2"
   FACTORY  = LOC(3^2 2^1) 01
   COMMENTS = "
 This jumper sets the Board Interrupt Request line.\n\n
 \tSet it to 3 for IRQ3 and to 2 for IRQ2."

JUMPER(5) = 2
   NAME     = "Jd2"
   JTYPE    = INLINE
   LABEL    = LOC(3^2 2^1) "1" "3"
   FACTORY  = LOC(3^2 2^1) 10
   COMMENTS = "
 This jumper sets the DMA Request line.\n\n
 \tSet it to 1 for DMA1 and to 3 for DMA3."

JUMPER(6) = 2
   NAME     = "Jd1"
   JTYPE    = INLINE
   LABEL    = LOC(3^2 2^1) "1" "3"
   FACTORY  = LOC(3^2 2^1) 10
   COMMENTS = "
 This jumper sets the DMA Acknowledge line.\n\n
 \tSet it to 1 for DMA1 and to 3 for DMA3."

SOFTWARE(1) = "
 To install the driver, the file 'ATALK.SYS'
 provided with the disk should be installed in
 the root directory of the boot disk.  The user
 must add a line to the CONFIG.SYS file on your
 boot disk.  The line must be of the form:\n
 \n
 DEVICE=ATALK.SYS /BOARDINT=x /DMA=y /ADDRESS=zzz /INT=aa /FLASHTALK=b\n
 \n
 where aa is any unused software interrupt,\n
 and b is 1 to enable FlashTalk and 0 to disable FlashTalk\n\n"

FUNCTION = "TOPS Network Connection"
   TYPE       = "NET"
   CONNECTION = "DB-9 Connector"
   COMMENTS   = "
 Disabling DMA will also disable high speed FlashTalk
 communications."
   HELP       = "
 Any AppleTalk compatible DB-9 connector can be used 
 with the FlashCard.  Simply attach the connector to
 the FlashCard, following the cabling end termination
 instructions included with the connector."
   CHOICE     = "DMA used"
      LINK
         IRQ  = 2 | 3
         INIT = JUMPER(4) LOC(3^2 2^1) 01 | 10
         INIT = SOFTWARE(1) "x=2"|"x=3"
      LINK
         DMA  = 1 | 3
         INIT = JUMPER(5) LOC(3^2 2^1) 10 | 01
         INIT = JUMPER(6) LOC(3^2 2^1) 10 | 01
         INIT = SOFTWARE(1) "y=1"|"y=3"
      LINK
         PORT = 0398h | 0390h | 0310h
         INIT = JUMPER(1) LOC(3^2 2^1) 10 | 10 | 01
         INIT = JUMPER(2) LOC(3^2 2^1) 10 | 10 | 10
         INIT = JUMPER(3) LOC(3^2 2^1) 01 | 10 | 10
         INIT = SOFTWARE(1) "zzz=398"|"zzz=390"|"zzz=310"

   CHOICE     = "DMA Not Used"
      FREE
         INIT = SOFTWARE(1) "y=none"
      LINK
         IRQ  = 2 | 3
         INIT = JUMPER(4) LOC(3^2 2^1) 01 | 10
	 INIT = SOFTWARE(1) "x=2"|"y=3"
      LINK
         PORT = 0398h | 0390h | 0310h
         INIT = JUMPER(1) LOC(3^2 2^1) 10 | 10 | 01
         INIT = JUMPER(2) LOC(3^2 2^1) 10 | 10 | 10
         INIT = JUMPER(3) LOC(3^2 2^1) 01 | 10 | 10
         INIT = SOFTWARE(1) "zzz=398"|"zzz=390"|"zzz=310"