;
; Barracuda Configuration File V1.0
;

BOARD
	ID		= "INP0010"
	NAME		= "Barracuda E/4810"
	MFR		= "Interphase Corp."
	CATEGORY	= "MSD"
	SLOT		= EISA
	LENGTH		= 330
	AMPERAGE	= 6500
	SKIRT		= NO
	READID		= YES
	BUSMASTER	= 50
	IOCHECK		= INVALID
	DISABLE		= SUPPORTED
	COMMENTS	= "The Barracuda is a single ported SCSI
			controller that may be turned into a dual ported
			SCSI controller with an optional daughter card."

;
; I/O Control Ports
;
IOPORT(1)		= 0zC8CH
	SIZE		= DWORD
	INITVAL		= 00000000000011xxxxxx000000001111b
	
;
; Jumpers
;
JUMPER(1)		= 1
	NAME		= "JX1"
	JTYPE		= PAIRED
	INITVAL		= LOC (1) x
	FACTORY		= LOC (1) 1
	COMMENTS	= "If this jumper is installed, the board will
			generate level triggered interrupts"

JUMPER(2)		= 1
	NAME		= "JA1"
	JTYPE		= PAIRED
	INITVAL		= LOC (1) 1
	FACTORY		= LOC (1) 1
	COMMENTS	= "Installing this jumper supplies terminator
			power to the SCSI bus.  The third LED indicates
			a failure of term power."
			
JUMPER(3)               = 11
        NAME            = "JAX1"
        JTYPE           = PAIRED
        REVERSE         = YES
        INITVAL         = LOC(1 2 3 4 5 6 7 8 9 10 11)11000000xxx
        FACTORY         = LOC(1 2 3 4 5 6 7 8 9 10 11)11000000000
        COMMENTS        = "JAX1 Jumpers set the SCSI ID for the primary
                        channel plus whether or not the SCSI bus is reset
                        on power up or board reset and whether or not the
                        4810 extended diagnostic is run on power up. With
                        JAX1 pins 1-2 installed, SCSI bus reset at power
                        on is not done and with JAX1 pins 3-4 installed, 
                        extended diagnostic is not performed."

JUMPER(4)               = 1
        NAME            = "JAX2"
        JTYPE           = PAIRED
        VERTICAL        = NO
        REVERSE         = NO
        INITVAL         = LOC(1) 1
        FACTORY         = LOC(1) 1
        COMMENTS        = "This jumper is used to isolate 36 MHZ OSC from
                        logic on the board. It is to be removed only for
                        manufacturing board test."

JUMPER(5)               = 1
        NAME            = "JA2"
        JTYPE           = PAIRED
        VERTICAL        = YES
        REVERSE         = NO
        INITVAL         = LOC(1) 1
        FACTORY         = LOC(1) 1
        COMMENTS        = "This jumper is used to isolate 24 MHZ processor
                        clock from logic on the board. It is to be removed
                        only for manufacturing board test."

JUMPER(6)               = 1
        NAME            = "JA4"
        JTYPE           = PAIRED
        VERTICAL        = YES
        REVERSE         = NO
        INITVAL         = LOC(1) 0
        FACTORY         = LOC(1) 0
        COMMENTS        = "The setting on this jumper should not be changed."

JUMPER(7)               = 1
        NAME            = "JA5"
        JTYPE           = PAIRED
        VERTICAL        = YES
        REVERSE         = NO
        INITVAL         = LOC(1) 1
        FACTORY         = LOC(1) 1
        COMMENTS        = "This jumper is used to isolate 24 MHZ SCSI clock
                        from Logic on the board. It is to be removed only
                        for manufacturing board test." 

JUMPER(8)               = 2
        NAME            = "JA6"
        JTYPE           = inline
        VERTICAL        = YES
        REVERSE         = NO
        INITVAL         = LOC(1^2 2^3) 00
        FACTORY         = LOC(1^2 2^3) 00
        COMMENTS        = "This is needed only if 256k (32k x 8) EPROMS
                        are used. 512k EPROMS are enabled by etch on the
                        board. If the etch is cut then the jumper must
                        be installed for 512k EPROMS."


FUNCTION 		= "Barracuda SCSI Channel"
	TYPE		= "MSD,HPFP"

	CHOICE = "SCSI Channel"

	LINK
		MEMORY = 4k
			ADDRESS = 0C8000h-0E7000h STEP = 4K
			MEMTYPE = OTH
			WRITABLE = YES
			SIZE = DWORD
			CACHE = NO
		INIT = IOPORT(1) LOC(17-12) 001000-100111

	SUBCHOICE
		FREE
		IRQ = 14|3|4|5|6|7|10|11|12|15
			SHARE = YES
			TRIGGER = LEVEL
			INIT = JUMPER(1) LOC(1) 1

	SUBCHOICE
		FREE
		IRQ = 14|3|4|5|6|7|10|11|12|15
			SHARE = YES
			TRIGGER = EDGE
			INIT = JUMPER(1) LOC(1) 0
		
FUNCTION 		= "Barracuda SCSI ID"

	CHOICE = "7"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 000

	CHOICE = "6"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 100

	CHOICE = "5"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 010

	CHOICE = "4"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 110

	CHOICE = "3"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 001

	CHOICE = "2"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 101

	CHOICE = "1"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 011

	CHOICE = "0"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 111