;-------------------------------------------------------
; ICL EtherTeam16 Configuration File, Vers 1.01 09/04/92
; Copyright International Computers Limited, 1992.
;-------------------------------------------------------
BOARD
 ID="ICLA010"
 NAME="ICL EtherTeam16 16 bit Ethernet Controller"
 MFR="ICL"
 CATEGORY="NET"
 SLOT=ISA16
 LENGTH=167
 SKIRT=NO
 READID=NO
 AMPERAGE=750
 IOCHECK=INVALID
 DISABLE=UNSUPPORTED
 COMMENTS =     "\n
		EtherTeam16 and EtherTeam16 TP are high
		performance, high reliability and easy
		of use Ethernet Adapters to be used in
		expansion slots with a 16-bit ISA
		standard bus.\n
		\n
		The I/O Base Address and the optional Boot
		PROM Address are set by jumpers. The IRQ
		Level and the Transceiver type are software
		selectable."

 HELP =         "\n
		Congratulations! You have selected EtherTeam16
		as your network adapter.\n"

;------------------
; I/O Base Address.
;------------------
JUMPER(1)=4
 NAME="JT1 I/O Base Address"
 JTYPE=PAIRED
 VERTICAL=NO
 REVERSE=NO
 LABEL=LOC(4-1) "IO290" "IO300" "IO310" "IO320"
 FACTORY=LOC(4-1) 0100
 COMMENTS="
 ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿\n
³               JT1 ÜÜÜÜ         ³\n
³                                ³\n
³                                ³\n
³                                ³\n
³                                ³\n
ÀÄÄÄÄÄ¿         Ú¿           Ú¿  ³\n
-     ÀÄÄÄÄÄÄÄÄÄÙÀÄÄÄÄÄÄÄÄÄÄÄÙÀÄÄÙ\n
\n"

;-------------------
; PROM Base Address.
;-------------------
JUMPER(2)=4
 NAME="JT2 PROM Base Address"
 JTYPE=PAIRED
 VERTICAL=NO
 REVERSE=NO
 LABEL=LOC(4-1) "CC000" "D8000" "DC000" "DISABLE"
 FACTORY=LOC(4-1) 0001
 COMMENTS="
 ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿\n
³                                ³\n
³               JT2 ÜÜÜÜ         ³\n
³                                ³\n
³                                ³\n
³                                ³\n
ÀÄÄÄÄÄ¿         Ú¿           Ú¿  ³\n
-     ÀÄÄÄÄÄÄÄÄÄÙÀÄÄÄÄÄÄÄÄÄÄÄÙÀÄÄÙ\n
\n"

;-------------------
; Software Settings.
;-------------------
SOFTWARE(1) =   "
		Software selection formats depend on the network
		operating system used. In LAN Manager, parameters
		are listed in the PROTOCOL.INI. In NetWare, they
		are either listed in NET.CFG or given in the LOAD
		command for ODI Drivers, or selected from the
		predefined configuration lists used by utilities
		like WSGEN or ROUTEGEN to generate Shell Drivers."

;-------------------------
; IO Base Address Choises.
;-------------------------
FUNCTION="EtherTeam16 Configuration Options"

SUBFUNCTION="IO Base Address"
 COMMENTS = "Reserves 10h area also from Base + 400h."
 CHOICE="300"
  LINK
   PORT = 300h - 30Fh
   INIT = JUMPER(1) LOC(4-1) 0100
   INIT = SOFTWARE(1) "\tI/O=300"

 CHOICE="290"
  LINK
   PORT = 290h - 29Fh
   INIT = JUMPER(1) LOC(4-1) 1000
   INIT = SOFTWARE(1) "\tI/O=290"

 CHOICE="310"
  LINK
   PORT = 310h - 31Fh
   INIT = JUMPER(1) LOC(4-1) 0010
   INIT = SOFTWARE(1) "\tI/O=310"

 CHOICE="320"
  LINK
   PORT = 320h - 32Fh
   INIT = JUMPER(1) LOC(4-1) 0001
   INIT = SOFTWARE(1) "\tI/O=320"

;---------------------------
; PROM Base Address Choises.
;---------------------------
SUBFUNCTION="PROM Base Address"
 COMMENTS = "Needed only if the BOOT PROM will be installed."
 CHOICE="Disabled"
  LINK
    INIT = JUMPER(2) LOC(4-1) 0001

 CHOICE="DC000"
  LINK
   MEMORY = 16K
    ADDRESS = 0DC000h
    WRITABLE = NO 
    MEMTYPE = OTH
    DECODE = 20
    INIT = JUMPER(2) LOC(4-1) 0010

 CHOICE="D8000"
  LINK
   MEMORY = 16K
    ADDRESS = 0D8000h
    WRITABLE = NO 
    MEMTYPE = OTH
    DECODE = 20
    INIT = JUMPER(2) LOC(4-1) 0100

 CHOICE="CC000"
  LINK
   MEMORY = 16K
    ADDRESS = 0CC000h
    WRITABLE = NO 
    MEMTYPE = OTH
    DECODE = 20
    INIT = JUMPER(2) LOC(4-1) 1000

;-------------------
; IRQ Level Choises.
;-------------------
SUBFUNCTION="Interrupt Level"
  COMMENTS = "IRQ2 is considered equivalent to IRQ9."
  CHOICE="IRQ 9"
    LINK
    IRQ=9
    INIT=SOFTWARE(1) "\tIRQ=9"
  CHOICE="IRQ 5"
    LINK
    IRQ=5
    INIT=SOFTWARE(1) "\tIRQ=5"
  CHOICE="IRQ 12"
    LINK
    IRQ=12
    INIT=SOFTWARE(1) "\tIRQ=12"
  CHOICE="IRQ 15"
    LINK
    IRQ=15
    INIT=SOFTWARE(1) "\tIRQ=15"