BOARD
	ID="HWP2090"
	NAME="HP Remote Assistant with On-Board Modem"
	MFR="Hewlett-Packard Co."
	CATEGORY="COM"
	SLOT=EISA
	LENGTH=330
;	AMPERAGE=1000
;	SKIRT=NO
	READID=YES
	BUSMASTER=50
;	IOCHECK=VALID
;	DISABLE=SUPPORTED

	HELP = 
"The HP Remote Assistant EISA Card is an intelligent communications card
which, when used with HP Remote Assistant software, provides remote server
management, including monitoring, management, and notification of server 
operations and events. Use the EISA Configuration Utility to configure the
interrupt channel and modem/serial ports. Use HP Remote Assistant
Configuration Utility (HPRAUTIL.EXE) to configure all other features."

IOPORT(1)=0z800h                        ;Serial Config port (serial port)
	INITVAL = XXXXXXXX                               
IOPORT(2)=0zC90h                        ;BMIC Mailbox Register 1 (command)
	INITVAL = XXXXXXXX
IOPORT(3)=0zC92h                        ;BMIC Mailbox Register 3 (data)
	INITVAL = XXXXXXXX
IOPORT(4)=0zC8Dh                        ;BMIC Local Doorbell
	INITVAL = XXXXXXXX

SOFTWARE(1) = 
"After adding the HP Remote Assistant EISA card to your EISA configuration, 
you must run the HP Remote Assistant Configuration Utility (HPRAUTIL.EXE) to 
complete the configuration of the board. The utility configures HP Remote 
Assistant features, including administrator names, passwords, pager numbers, 
threshold values and notifications."

FUNCTION = "Send BMIC Command (BIOS Init)"
	SHOW=no
	CHOICE = "Send Cmd"
		DISABLE = NO
		FREE
		INIT = IOPORT(2)  LOC(7-0)	01000010
		INIT = IOPORT(4)  LOC(7-0)	00000001

FUNCTION = "Serial Interface Configuration"
	TYPE = "COM"
	HELP = 
"This option specifies how the HP Remote Assistant's modem and/or 9-pin
port will be used. COMx - SERVER MGMT WITH FILE TRANSFER (default) provides
complete functionality of HP Remote Assistant and requires the card to map to
one of the four COM ports. NONE - SERVER MGMT WITHOUT FILE TRANSFER is used 
if there is not a COM port available. All HP Remote Assistant features are
enabled except DOS-level file transfer.
COMx - PASSTHRU MODE causes the board to function as a standard internal modem 
or serial port. (This is not recommended because it disables the server
management features that require the modem or serial port.)"

	CHOICE = "COM1 (Server Mgmt with File Transfer)"
		SUBTYPE = "COM1"
		LINK
		IRQ = 4
			SHARE = NO
			TRIGGER = EDGE
		PORT = 03F8h-03FFh
			SHARE = NO
			SIZE = BYTE
		INIT = IOPORT(1)  LOC(7 2 1 0) 0001
		INIT = IOPORT(3)  LOC(7 2 1 0) 0001

	CHOICE = "COM2 (Server Mgmt with File Transfer)"
		SUBTYPE = "COM2"
		LINK
		IRQ = 3
			SHARE = NO
			TRIGGER = EDGE
		PORT = 02F8h-02FFh
			SHARE = NO
			SIZE = BYTE
		INIT = IOPORT(1)  LOC(7 2 1 0) 0011
		INIT = IOPORT(3)  LOC(7 2 1 0) 0011

	CHOICE = "COM3 (Server Mgmt with File Transfer)"
		SUBTYPE = "COM3"
		LINK
		IRQ = 10
			SHARE = NO
			TRIGGER = EDGE
		PORT = 03E8h-03EFh
			SHARE = NO
			SIZE = BYTE
		INIT = IOPORT(1)  LOC(7 2 1 0) 0101
		INIT = IOPORT(3)  LOC(7 2 1 0) 0101

	CHOICE = "COM4 (Server Mgmt with File Transfer)"
		SUBTYPE = "COM4"
		LINK
		IRQ = 11
			SHARE = NO
			TRIGGER = EDGE
		PORT = 02E8h-02EFh
			SHARE = NO
			SIZE = BYTE
		INIT = IOPORT(1)  LOC(7 2 1 0) 0111
		INIT = IOPORT(3)  LOC(7 2 1 0) 0111

	CHOICE = "None (Server Mgmt without File Transfer)"
		DISABLE = NO
		FREE
		INIT = IOPORT(1)  LOC(7 2 1 0) 0000
		INIT = IOPORT(3)  LOC(7 2 1 0) 0000

	CHOICE = "COM1 (Passthru Mode)"
		SUBTYPE = "COM1"
		LINK
		IRQ = 4
			SHARE = NO
			TRIGGER = EDGE
		PORT = 03F8h-03FFh
			SHARE = NO
			SIZE = BYTE
		INIT = IOPORT(1)  LOC(7 2 1 0) 1001
		INIT = IOPORT(3)  LOC(7 2 1 0) 1001

	CHOICE = "COM2 (Passthru Mode)"
		SUBTYPE = "COM2"
		LINK
		IRQ = 3
			SHARE = NO
			TRIGGER = EDGE
		PORT = 02F8h-02FFh
			SHARE = NO
			SIZE = BYTE
		INIT = IOPORT(1)  LOC(7 2 1 0) 1011
		INIT = IOPORT(3)  LOC(7 2 1 0) 1011

	CHOICE = "COM3 (Passthru Mode)"
		SUBTYPE = "COM3"
		LINK
		IRQ = 10
			SHARE = NO
			TRIGGER = EDGE
		PORT = 03E8h-03EFh
			SHARE = NO
			SIZE = BYTE
		INIT = IOPORT(1)  LOC(7 2 1 0) 1101
		INIT = IOPORT(3)  LOC(7 2 1 0) 1101

	CHOICE = "COM4 (Passthru Mode)"
		SUBTYPE = "COM4"
		LINK
		IRQ = 11
			SHARE = NO
			TRIGGER = EDGE
		PORT = 02E8h-02EFh
			SHARE = NO
			SIZE = BYTE
		INIT = IOPORT(1)  LOC(7 2 1 0) 1111
		INIT = IOPORT(3)  LOC(7 2 1 0) 1111



FUNCTION = "Interrupt Channel (IRQ)"
	HELP =
"This option sets the IRQ number for the HP Remote Assistant EISA 
card. Leave this option disabled unless you are using a specific 
software function that requires an IRQ."

	CHOICE = "Disabled"
		FREE
		INIT=IOPORT(1) LOC(6-3) 0000B	
		INIT=IOPORT(3) LOC(6-3) 0000B	

	CHOICE = "IRQ 5"
		LINK
		IRQ = 5
		SHARE = NO
		TRIGGER = EDGE
		INIT=IOPORT(1) LOC(6-3) 1001B
		INIT=IOPORT(3) LOC(6-3) 1001B

	CHOICE = "IRQ 10"
		LINK
		IRQ = 10
		SHARE = NO
		TRIGGER = EDGE
		INIT=IOPORT(1) LOC(6-3) 1011B
		INIT=IOPORT(3) LOC(6-3) 1011B

	CHOICE = "IRQ 12"
		LINK
		IRQ = 12
		SHARE = NO
		TRIGGER = EDGE
		INIT=IOPORT(1) LOC(6-3) 1101B
		INIT=IOPORT(3) LOC(6-3) 1101B

	CHOICE = "IRQ 15"
		LINK
		IRQ =  15
		SHARE = NO
		TRIGGER = EDGE
		INIT=IOPORT(1) LOC(6-3) 1111B
		INIT=IOPORT(3) LOC(6-3) 1111B