BOARD
	ID = "HWP2011"
	NAME = "HP NetServer LD Pro System Board (CFG 1.22)"
	MFR = "Hewlett-Packard Co."
	CATEGORY = "SYS"
	AMPERAGE = 19000
	SLOT=EMB(0)
	READID=YES
	COMMENTS = ""
	HELP=""

SYSTEM
; (1.15.2) Modified NVRAM size
	NONVOLATILE = 6K
	SLOT(0)=EISA(0) LABEL="System"
	SLOT(1)=PCI(0,10) LABEL = "SCSI"
	SLOT(2)=OTHER(14), "ADP7880" LABEL="SCSI"
;LD Pro <1.02>	SLOT(3)=PCI(0,11) LABEL = "SCSI B"
;LD Pro <1.02>	SLOT(4)=OTHER(15), "ADP7880" LABEL="SCSI B"
	SLOT(5)=PCI(0,7) LABEL = "PCI 9"
	SLOT(6)=PCI(1,1) LABEL = "PCI 8"
	SLOT(7)=PCI(1,2) LABEL = "PCI 7"
	SLOT(8)=PCI(1,3) LABEL = "PCI 6"
;LD Pro <1.02> These connectors are not loaded for LD Pro
;LD Pro <1.02>	SLOT(9)=EISA - PCI(5,1,4) LABEL = "SHARED 5"
;LD Pro <1.02>	LENGTH=341
;LD Pro <1.02>	BUSMASTER=YES
	SLOT(10)=EISA(4) LABEL="EISA 4"
		LENGTH=341
		BUSMASTER=YES
	SLOT(11)=EISA(3) LABEL="EISA 3"
		LENGTH=341
		BUSMASTER=YES
;LD Pro <1.02>	SLOT(12)=EISA(2) LABEL="EISA 2"
;LD Pro <1.02>		LENGTH=341
;LD Pro <1.02>		BUSMASTER=YES
;LD Pro <1.02>	SLOT(13)=EISA(1) LABEL="EISA 1"
;LD Pro <1.02>		LENGTH=341
;LD Pro <1.02>		BUSMASTER=YES
; (1.20.1) (1.19.4) add nos resource reservation support
;  	SLOT(14)= OTHER(13), "HWP21D0" LABEL="NOS"

SWITCH(1)=1
	NAME="FLASH WRITE ENABLE"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "1"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="1 ON  = BIOS is unlocked (can be updated).
		\n1 OFF = BIOS is locked (cannot be updated)."

SWITCH(2)=1
	NAME="BOOT BLOCK DISABLE"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "2"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="2 ON  = BIOS Boot Block is Disabled.
		\n2 OFF = BIOS Boot Block is Enabled."


SWITCH(3)=1
	NAME="CONFIG VALID"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "3"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="3 ON  = Configuration information is preserved.
		\n3 OFF = Configuration information is cleared."

SWITCH(4)=1
	NAME="CONFIG UNLOCK"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "4"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="4 ON  = Configuration information is unlocked.
		\n4 OFF = Configuration information is locked."

SWITCH(5)=1
	NAME="PASSWORD ENABLE"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "5"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="5 ON  = Password is preserved and enabled.
		\n5 OFF = Password is erased and disabled."

SWITCH(6)=1
	NAME="NMI LOG ENABLE"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "6"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="6 ON  = NMI events are logged in the Event Log.
		\n6 OFF = NMI events are not logged in the Event Log."

SWITCH(7)=1
	NAME="I/O CTRL ENABLE"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "7"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="7 ON  = System board I/O controller enabled.
		\n        You must enable this switch in order to use any
		\n        of the on board peripheral devices.
		\n7 OFF = System board I/O controller disabled."

SWITCH(8)=1
	NAME="VIDEO ENABLE"
	STYPE=DIP
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(1) "8"
	FACTORY=LOC(1) 1
	INITVAL=LOC(1) 1
	COMMENTS="8 ON  = System board VGA controller enabled.
		\n8 OFF = System board VGA controller disabled.
		\n        Set this switch to OFF if you replace 
		\n        the system board VGA controller with
		\n        an EISA or ISA video card."

include = "HWP2011.OVL"

;********************
;* EISA NMI Control *
;********************

IOPORT(1) = 461h                ;EISA Extended NMI Control Register:
    SIZE = BYTE                 ; bit 1 - Software NMI enable
    INITVAL = 0000xxx0          ; bit 3 - bus timeout NMI enable

FUNCTION = "EISA NMI Control"
SHOW=EXP
  HELP = "These functions control the initialization of port 461h which
	  controls EISA Non-maskable interrupts."

  SUBFUNCTION = "Software Generated NMI"
  HELP =" If the software generated NMI is enabled, any output to I/O port 462h 
	  will cause port 461h bit 5 to be set and an NMI to be generated."
    CHOICE = "Disabled" FREE INIT = IOPORT(1) LOC(1) 0
    CHOICE = "Enabled"  FREE INIT = IOPORT(1) LOC(1) 1

  SUBFUNCTION = "Bus Timeout NMI"
    HELP = "If the bus timeout NMI is enabled, an EISA device holding the 
	bus more than 64 BCLKs, or a memory slave extending the cycle more 
	than 256 BCLKs, will cause port 461h bit 6 to be set, an NMI to be 
	generated and the system board to assert RESDRV."
    CHOICE = "Disabled" FREE INIT = IOPORT(1) LOC(3) 0
    CHOICE = "Enabled"  FREE INIT = IOPORT(1) LOC(3) 1

  SUBFUNCTION = "Fail-Safe Timer Timeout NMI"
    HELP = "If the fail-safe timer timeout NMI is enabled, the fail-safe 
	timer expiring before being reset by a software routine will
	cause port 461h bit 7 to be set and an NMI to be generated." 
    CHOICE = "Disabled" FREE INIT = IOPORT(1) LOC(2) 0
    CHOICE = "Enabled"  FREE INIT = IOPORT(1) LOC(2) 1

;*******************************
;* ADVANCED PCI DEVICE CONTROL *
;*******************************

FUNCTION = "PCI Bridge Timers"
SHOW=EXP
HELP = "A live-lock condition can occur if the Bridge Request Mask and Wait
	Timers are left disabled for DEC 21050 and 21052 PCI to PCI bridge chips 
        used on the motherboard of this system or on add-in cards.
	\n\nDo not disable the PCI Bridge Timers unless 
	instructed to do so by the system manufacturer."
COMMENTS = "Do not disable the PCI Bridge Timers unless 
	   instructed to do so by the system manufacturer."
; (1.19.3){
    CHOICE = "16 PCI Clock Cycle"   SUBTYPE = "PCI;CMOS=61F902"
    CHOICE = "32 PCI Clock Cycle"   SUBTYPE = "PCI;CMOS=61F904"
    CHOICE = "64 PCI Clock Cycle"   SUBTYPE = "PCI;CMOS=61F906"
    CHOICE = "Disabled"  			SUBTYPE = "PCI;CMOS=61F900"
; }(1.19.3)

FUNCTION = "PCI Busmaster Control During Boot"
SHOW=EXP
  HELP = "A <Ctrl><Alt><Del> warm boot under MS-DOS can cause the system
	to hang or exhibit other strange behavior if a PCI busmaster device 
	is still using system memory when the BIOS warm start sequence
	begins.  Disabling busmastering for a device during the BIOS boot 
	sequence can eliminate this problem.
	\n\nIf busmastering is disabled by the system BIOS during boot, a 
	driver for the device must enable busmastering for the device to 
	behave properly"
SUBFUNCTION = "Slot 9 Busmaster"
HELP = "This function enables or disables busmastering during boot for a 
	busmaster device in slot 9."
    CHOICE = "Enabled"   SUBTYPE = "PCI;CMOS=6AFF04"
    CHOICE = "Disabled"  SUBTYPE = "PCI;CMOS=6AFB00"

SUBFUNCTION = "SCSI Busmaster"
HELP = "This function enables or disables busmastering during boot for the 
	embedded PCI SCSI controller."
    CHOICE = "Enabled"   SUBTYPE = "PCI;CMOS=6BFF04"
    CHOICE = "Disabled"  SUBTYPE = "PCI;CMOS=6BFB00"

;LD Pro <1.02> SUBFUNCTION = "SCSI B Busmaster"
;LD Pro <1.02> HELP = "This function enables or disables busmastering during boot for the 
;LD Pro <1.02>	embedded PCI SCSI B controller."
;LD Pro <1.02>    CHOICE = "Enabled"   SUBTYPE = "PCI;CMOS=6CFF04"
;LD Pro <1.02>    CHOICE = "Disabled"  SUBTYPE = "PCI;CMOS=6CFB00"

; (1.19.2){  Change Dimm logging function to Virtual Wire Mode
FUNCTION = "Virtual-Wire Mode"
SHOW = EXP
	CHOICE = "Local APIC"	SUBTYPE = "APIC;CMOS=66BF00"
	CHOICE = "I/O APIC"		SUBTYPE = "APIC;CMOS=66BF40"
; }(1.19.2)

; (1.18.4){
FUNCTION = "MPS Specification"
SHOW = EXP
	CHOICE = "MPS 1.1"		SUBTYPE = "MPS;CMOS=67BF00"
	CHOICE = "MPS 1.4"		SUBTYPE = "MPS;CMOS=67BF40"
; }(1.18.4)

;***************************
;* RAM Cache Configuration *
;***************************

GROUP = "RAM Cache Option"
; (1.13.2){ RAM caching 
FUNCTION = "RAM Cache Option (00000-C7FFF)"
SHOW=EXP
  SUBFUNCTION = "Cache Option for 0-512K"
    CHOICE = "Write Back"   	SUBTYPE = "CACHE;CMOS=66f806"
    CHOICE = "Write Through"   	SUBTYPE = "CACHE;CMOS=66f804"
;    CHOICE = "USWC"   			SUBTYPE = "CACHE;CMOS=66f801"
;    CHOICE = "WP"   			SUBTYPE = "CACHE;CMOS=66f805"
    CHOICE = "Disabled"  		SUBTYPE = "CACHE;CMOS=66f800"
  SUBFUNCTION = "Cache Option for 512K-640K"
    CHOICE = "Write Back"   	SUBTYPE = "CACHE;CMOS=66c730"
    CHOICE = "Write Through"   	SUBTYPE = "CACHE;CMOS=66c720"
;    CHOICE = "USWC"   			SUBTYPE = "CACHE;CMOS=66c708"
;    CHOICE = "WP"   			SUBTYPE = "CACHE;CMOS=66c728"
    CHOICE = "Disabled"  		SUBTYPE = "CACHE;CMOS=66c700"
  SUBFUNCTION = "Cache Option for A0000-BFFFF"
; (1.15a.2) get rid of USWC choice for video RAM
    CHOICE = "Disabled"  		SUBTYPE = "CACHE;CMOS=67f800"
;    CHOICE = "Write Back"   	SUBTYPE = "CACHE;CMOS=67f806"
;    CHOICE = "Write Through"   	SUBTYPE = "CACHE;CMOS=67f804"
;    CHOICE = "USWC"   			SUBTYPE = "CACHE;CMOS=67f801"
;    CHOICE = "Write Protect"   			SUBTYPE = "CACHE;CMOS=67f805"
  SUBFUNCTION = "Cache Option for C0000-C7FFF"
; (1.15a.1) default A0000-FFFFF region to cache disable
    CHOICE = "Disabled"  		SUBTYPE = "CACHE;CMOS=67c700"
    CHOICE = "Write Protect"   			SUBTYPE = "CACHE;CMOS=67c728"
;    CHOICE = "Write Back"   	SUBTYPE = "CACHE;CMOS=67c730"
;    CHOICE = "Write Through"   	SUBTYPE = "CACHE;CMOS=67c720"
;    CHOICE = "USWC"   			SUBTYPE = "CACHE;CMOS=67c708"

FUNCTION = "RAM Cache Option (C8000-FFFFF)"
SHOW = EXP
  SUBFUNCTION = "Cache Option for C8000-CFFFF"				 
; (1.15a.1) default A0000-FFFFF region to cache disable
    CHOICE = "Disabled"  		SUBTYPE = "CACHE;CMOS=68f800"
    CHOICE = "Write Protect"   	SUBTYPE = "CACHE;CMOS=68f805"
    CHOICE = "Write Back"   	SUBTYPE = "CACHE;CMOS=68f806"
    CHOICE = "Write Through"   	SUBTYPE = "CACHE;CMOS=68f804"
;    CHOICE = "USWC"   			SUBTYPE = "CACHE;CMOS=68f801"

  SUBFUNCTION = "Cache Option for D0000-D7000"
    CHOICE = "Disabled"  		SUBTYPE = "CACHE;CMOS=68c700"
    CHOICE = "Write Back"   	SUBTYPE = "CACHE;CMOS=68c730"
    CHOICE = "Write Through"   	SUBTYPE = "CACHE;CMOS=68c720"
;    CHOICE = "USWC"   			SUBTYPE = "CACHE;CMOS=68c708"
    CHOICE = "Write Protect"   			SUBTYPE = "CACHE;CMOS=68c728"
  SUBFUNCTION = "Cache Option for D8000-DFFFF"				 
    CHOICE = "Disabled"  		SUBTYPE = "CACHE;CMOS=69f800"
    CHOICE = "Write Back"   	SUBTYPE = "CACHE;CMOS=69f806"
    CHOICE = "Write Through"   	SUBTYPE = "CACHE;CMOS=69f804"
;    CHOICE = "USWC"   			SUBTYPE = "CACHE;CMOS=69f801"
    CHOICE = "Write Protect"   			SUBTYPE = "CACHE;CMOS=69f805"
; (1.18.6) disable the cache option for e0000-fffff
  SUBFUNCTION = "Cache Option for E0000-FFFFF"
; (1.15a.1) default A0000-FFFFF region to cache disable
    CHOICE = "Disabled"  		SUBTYPE = "CACHE;CMOS=69c700"
;    CHOICE = "Write Protect"   			SUBTYPE = "CACHE;CMOS=69c728"
;    CHOICE = "Write Back"   	SUBTYPE = "CACHE;CMOS=69c730"
;    CHOICE = "Write Through"   	SUBTYPE = "CACHE;CMOS=69c720"
;    CHOICE = "USWC"   			SUBTYPE = "CACHE;CMOS=69c708"

; (1.18.2){
FUNCTION = "Extended Memory Cache Option"
SHOW = EXP
    CHOICE = "Write Back"   	SUBTYPE = "CACHE;CMOS=558f60"
    CHOICE = "Write Through"   	SUBTYPE = "CACHE;CMOS=558f40"
    CHOICE = "Disabled"  		SUBTYPE = "CACHE;CMOS=558f00"
; }(1.18.2)

ENDGROUP


;**************************
;* SYSTEM BOARD RESOURCES *
;**************************

GROUP = "Basic Main Board Functions"
  TYPE = "SYS"

FUNCTION = "Timer"
; (1.18.3) change product number and SPU number
  TYPE = "HP_PC,NAME=NETSERVER LD PRO,SPU_NUM=52"
  SHOW = NO
  CHOICE = "Reserved"
    FREE
      IRQ = 0
	TRIGGER = EDGE

FUNCTION = "Keyboard"
  SHOW = NO
  TYPE = "KEY"
  CHOICE = "101 Key"
    SUBTYPE = "101"
    LINK
      IRQ = 1
	TRIGGER = EDGE
      PORT = 60H
      PORT = 64H

FUNCTION = "Real-time Clock"
  SHOW = NO
  CHOICE = "Reserved"
    FREE
      IRQ = 8
	TRIGGER = EDGE
      PORT = 70H - 71H

FUNCTION = "Chip Set"
  SHOW = NO
; (1.16.2)change a hidden function name to "pmc" from "TXC"
  CHOICE = "PMC"
    LINK
      PORT = 0CF8h-0CFFh

FUNCTION = "SuperIO"
  SHOW = NO
  CHOICE = "SIO"
    LINK
      PORT = 0398h-0399h

FUNCTION = "ESC chip"
  SHOW = NO
  CHOICE = "ESC"
    LINK
      PORT = 022h-023h


FUNCTION = "System BIOS ROM"
	SHOW = NO
	CHOICE = "System BIOS ROM"
    FREE MEMORY=128K ADDRESS=0E0000h WRITABLE=NO MEMTYPE=OTH CACHE=YES

ENDGROUP


FUNCTION = "PCI SCSI Boot Priority Order"
COMMENTS = "The boot priority for PCI SCSI adapters is
	    controlled by the order adapters 
	    are scanned by the system.  The embedded SCSI  
	    controller can be scanned (and given a chance to boot from 
	    an attached device) before or after add-in PCI adapters.\n\n
	    CAUTION: Press F1, then 'Selected item' for help,
	    or read the 'SCSI Boot Priority' 
	    section of Information Assistant on the Navigator CD.\n" 
HELP = "The SCSI  
	controller can be scanned (and given a chance to boot from 
	an attached device) before or after add-in PCI adapters.\n\n
	Concerns:\n
	If the system has many adapters w/ BIOSes installed, and this function
	is set to 'PCI adapters before SCSI', adapter BIOSes may
	fill the memory range for option ROMs.  There may not be room
	to load the SCSI BIOS and the system may not 
	boot from the Navigator CD.\n\n
	If there are EISA or ISA adapters installed in the system, they 
	can affect the PCI SCSI adapter boot order.\n\n
	If either concern applies, please read the 'SCSI Boot Priority' 
	section of Information Assistant on the Navigator CD.\n" 
	CHOICE = "SCSI before PCI adapters"
	 SUBTYPE = "MSD;SCSI;CMOS=51DF00"
	CHOICE = "PCI adapters before SCSI"
	 SUBTYPE = "MSD;SCSI;CMOS=51FF20"



INCLUDE="!ADP7880.CFG",14
; LD Pro <1.02>	INCLUDE="!ADP7880.CFG",15
; (1.20.1) (1.19.4)
;INCLUDE="!HWP21D0.CFG",13