;
; (C)Copyright Hewlett-Packard Co., 1989-1990
;    All Rights Reserved.
;

BOARD
   ID	    = "HWP0060"
   NAME     = "HP Intelligent Graphics Controller 10 (A1086A)"
   MFR	    = "Hewlett-Packard Co."
   CATEGORY = "VID"
   SLOT     = ISA8OR16
   COMMENTS = "
 The Intelligent Graphics Controller 10 provides high-resolution
 video graphics capability to your personal computer's high-resolution
 monitor.  Both single (VGA pass-through) and dual monitor configurations
 are supported."

SWITCH(1) = 4
   NAME     = "configuration switch"
   STYPE    = DIP
   REVERSE  = YES
   LABEL    = LOC(1-4) "A1" "A0" "16" "XS"
   COMMENTS = "
 the diagram has the direction of the switches
 backwards from the actual switch.\n
 0 on the switch corresponds to off in the diagram and\n
 1 on the switch corresponds to on in the diagram."

JUMPER(1) = 2
   NAME     = "DRAM single jumper"
   JTYPE    = INLINE
   FACTORY  = LOC(1^2 2^3) 01
   LABEL    = LOC(1^2 2^3)  "0k" "512k"

JUMPER(2) = 10
   NAME     = "Left VRAM"
   JTYPE    = TRIPOLE
   VERTICAL = YES
   FACTORY  = LOC(1-10) 1111111111

JUMPER(3) = 10
   NAME     = "Right VRAM"
   JTYPE    = TRIPOLE
   VERTICAL = YES
   FACTORY  = LOC(1-10) 1111111111

JUMPER(4) = 2
   NAME     = "Two single VRAM"
   JTYPE    = TRIPOLE
   VERTICAL = YES
   FACTORY  = LOC(1-2) 11

SOFTWARE(1) = "
 When you execute the Intelligent Graphics Controller
 configuration utility IGCSETUP you must provide the
 following data when you are prompted:\n\n
 \tThe amount of VRAM and DRAM you have installed.\n
 \tThe type and resolution of the monitor you will be using.\n
 \tThe number of simultaneous colors.\n
 and:\n\n"


FUNCTION = "Video Operations"
   TYPE        = "VID"
   HELP        = "
 You may have more DRAM on the Extension Module,
 but the 512k or 0k only refers to memory
 on the main board."
   SUBFUNCTION = "DRAM on the main board."
      CHOICE = "512K"
	 FREE
	    INIT = JUMPER(1) LOC(1^2 2^3) 01
      CHOICE = "0k"
	 FREE
	    INIT = JUMPER(1) LOC(1^2 2^3) 10

   SUBFUNCTION = "VRAM"
      COMMENTS = "
 Select the 8 planes choice if you
 have the Extension Module installed."
      CHOICE = "4 Planes"
	 FREE
	    INIT = JUMPER(2) LOC(1-10) 1111111111
	    INIT = JUMPER(3) LOC(1-10) 1111111111
	    INIT = JUMPER(4) LOC(1-2) 11
      CHOICE = "8 Planes"
	 FREE
	    INIT = JUMPER(2) LOC(1-10) 0000000000
	    INIT = JUMPER(3) LOC(1-10) 0000000000
	    INIT = JUMPER(4) LOC(1-2) 00

   SUBFUNCTION = "Composite Sync"
      HELP = ""
      CHOICE = "Sync signal on RGB input"
	 FREE
	    INIT = SWITCH(1) LOC(4) 0
      CHOICE = "Separate sync signal"
	 FREE
	    INIT = SWITCH(1) LOC(4) 1

   SUBFUNCTION = "Data Transfer Mode"
      CHOICE = "16 bit"
	 FREE
	    INIT = SWITCH(1) LOC(3) 0
      CHOICE = "8 bit"
	 FREE
	    INIT = SWITCH(1) LOC(3) 1

   SUBFUNCTION = "I/O base address"
      CHOICE = "250h"
	 LINK
	    PORT = 0250h-025Bh
	    INIT = SWITCH(1) LOC(1 2) 00
	    INIT = SOFTWARE(1) "I/O base = 250h"
      CHOICE = "290h"
	 LINK
	    PORT = 0290h-029Bh
	    INIT = SWITCH(1) LOC(1 2) 01
	    INIT = SOFTWARE(1) "I/O base = 290h"
      CHOICE = "350h"
	 LINK
	    PORT = 0350h-035Bh
	    INIT = SWITCH(1) LOC(1 2) 10
	    INIT = SOFTWARE(1) "I/O base = 350h"