;------------------------------------------------------
; DTC Host Adapter Configuration File
; Update Date : June. 1, 1992
; By : Alex Wang
;
; This file is grab from !dtc1102.cfg.
; ->Modified floppy controller setting .
; ->Modified display jumper setting for 3.5", 2.88Mb floppy drive support.
; ->Modified the secondary hard drive port bits location setting.
;------------------------------------------------------
BOARD
   ID = "DTC1103"
   NAME = "DTC2290 EISA IDE Controller"
   MFR = "Data Technology"
   CATEGORY = "MSD"
   SLOT=EISA
   LENGTH=195
   AMPERAGE = 1500
   READID = NO                  
   IOCHECK = INVALID
   DISABLE = UNSUPPORTED

   COMMENTS = "
 DTC2290 is a high performance EISA IDE controller.\n
The features of this board are:\n
- Fully EISA Compatible\n
- Supports multiple sectors transfer\n
- Supports 32 bits Data Transfers\n
- Supports drive over 512 MB\n
- Support 8Mbytes/sec Data Transfer Rate\n
- Support 2 IDE ports with up to 4 IDE Drives\n
- Support up to 4 Floppy Disk Drives"

JUMPER(1)=4
	NAME="JUMPER W1 THRU W4"
	JTYPE=PAIRED
	VERTICAL=YES
	REVERSE=NO
	LABEL=LOC(4 3 2 1) "W4-DTC/IBM""W3-BIOSEN""W2-ALTMEM1""W1-ALTMEM2"
	INITVAL=LOC(4 3 2 1) xxxx
	FACTORY=LOC(4 3 2 1) 0000
	HELP="
The DTC2x90 on-board BIOS is\n
enabled when W3 is installed.\n
The address where the BIOS is 
located is defined by W1 and W2;\n
such that when\n
W1 - OPENED and W2 - OPENED then\n
BIOS range is C8000 to CBFFF\n
W1 - OPENED and W2 - CLOSED then\n
BIOS range is D0000 to D3FFF\n
W1 - CLOSED and W2 - CLOSED then\n
BIOS range is D4000 to D7FFF\n
W1 - CLOSED and W2 - OPENED then\n
BIOS range is D8000 to DBFFF.\n
OPEN W4 if a twisted ribbon\n
cable is used.  CLOSE W4 if\n
a flat ribbon cable is used." 

JUMPER(2)=6                             
	NAME="JUMPER W5 THRU W10"       
	JTYPE=PAIRED
	VERTICAL=NO
	REVERSE=NO  
	LABEL=LOC(6 5 4 3 2 1) "W10 B:2.88""W9 A:2.88"
			       "W8 DRV3""W7 DRV2""W6 DRV1""W5 DRV0"
	INITVAL=LOC(6 5 4 3 2 1) xxxxxx
	FACTORY=LOC(6 5 4 3 2 1) 000000
	HELP="
Jumper W5 through W8 is used by\n
the DTC2x90 to translate drive\n
parameters for each attached\n
drive as though they have\n
64 heads with 63 sectors/track.\n
W5 CLOSED maps Port 1 Master.\n
W6 CLOSED maps Port 1 SLAVE.\n
W7 CLOSED maps Port 2 Master.\n
W8 CLOSED maps Port 2 SLAVE."

; Use to set up port speed

IOPORT(1) = 0ZC74h
   INITVAL = LOC(7-0) xxxxxxxx  

FUNCTION = "IDE Subsystem"
  TYPE = "MSD"

; Choices that have been commented out have not
; been tested but reflect manufacturer's specification
; for maximum host data transfer.

  SUBFUNCTION = "SET DATA TRANSFER RATE FOR PORT 1"
    COMMENTS = "This setting is used to maximize the data\n
transfer that an attached drive can sustain."
    HELP = "
This setting is used to maximize\n
the data transfer that the drive\n 
	  can sustain.\n
----------- CAUTION ------------\n
If there are two drives attached\n
to one port, you must choose the\n
slower drive's speed for that port."

	CHOICE = "MODE 0                          3.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 0000
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "MODE 1                          5.1MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1110
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "MODE 2                          8.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1010
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "BRAND BT9170A/BT9220A           7.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1001
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "CONNER CP3000/CP3024/CP3044     4.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1100
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "CONNER CP30104                  4.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1100
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "CONNER CP30204                  8.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1010
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "FUJITSU M2614ET                 3.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 0000
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "FUJITSU M2622T/M2623T/M2624T    7.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1001
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "HP C2233/C2234/C2235            6.2MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1000
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "MAXTOR LXT7120A                 3.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 0000
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "MAXTOR LXT7213A                 8.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1010
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "MAXTOR LXT213A                  4.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 0011
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE
  
	CHOICE = "MAXTOR LXT340A                  8.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1010
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "QUANTUM LPS52AT                 4.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 0011
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "QUANTUM LPS120AT/LPS240AT       4.6MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1101
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SEAGATE ST1400A/ST1401A/ST1480A 4.0MB/S"
	   LINK                           
		INIT = IOPORT(1) LOC(3-0) 0011
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "WESTERN DIGITAL WDAC2120        4.0MB/S"
	   LINK                           
		INIT = IOPORT(1) LOC(3-0) 0011
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "WESTERN DIGITAL WDAP4200        4.6MB/S"
	   LINK                           
		INIT = IOPORT(1) LOC(3-0) 1101
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED K                         8.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1010
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED J                         7.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1001
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED I                         6.2MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1000
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED H                         5.6MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1111
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED G                         5.1MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1110
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED F                         4.6MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1101
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED E                         4.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 1100
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED D                         4.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 0011
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED C                         3.7MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 0010
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED B                         3.5MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 0001  
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED A                         3.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(3-0) 0000  
		PORT=1F0h-1F7h
		IRQ=14
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "DISABLED"                       
	   LINK
		INIT = IOPORT(1) LOC(3-0) 0000  
		
  SUBFUNCTION = "SET DATA TRANSFER RATE FOR PORT 2"
    COMMENTS = "This setting is used to maximize the data\n
transfer that an attached drive can sustain.\n"
    HELP="
This setting is used to maximize\n 
the data transfer that the drive\n
	  can sustain.\n
----------- CAUTION ------------\n
If there are two drives attached\n
to one port, you must choose the\n
slower drive's speed for that port."

	CHOICE = "MODE 0                          3.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 0000
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "MODE 1                          5.1MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1110
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "MODE 2                          8.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1010
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "BRAND BT9170A/BT9220A           7.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1001
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "CONNER CP3000/CP3024/CP3044     4.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1100
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		   TRIGGER=EDGE

	CHOICE = "CONNER CP30104                  4.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1100
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "CONNER CP30204                  8.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1010
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "FUJITSU M2614ET                 3.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 0000
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE
 
	CHOICE = "FUJITSU M2622T/M2623T/M2624T    7.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1001
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "HP C2233/2234/2235              6.2MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1000
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "MAXTOR LXT7120A                 3.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 0000
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "MAXTOR LXT7213A                 8.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1010
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE


	CHOICE = "MAXTOR LXT213A                  4.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 0011
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "MAXTOR LXT340A                  8.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1010
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "QUANTUM LPS52AT                 4.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 0011
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "QUANTUM LPS120AT/LPS240AT       4.6MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1101
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SEAGATE ST1400A/ST1401A/ST1480A 4.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 0011
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "WESTERN DIGITAL WDAC2120        4.0MB/S"
	   LINK                           
		INIT = IOPORT(1) LOC(7-4) 0011
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "WESTERN DIGITAL WDAP4200        4.6MB/S"
	   LINK                           
		INIT = IOPORT(1) LOC(7-4) 1101
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED K                         8.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1010
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED J                         7.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1001
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED I                         6.2MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1000
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED H                         5.6MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1111
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED G                         5.1MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1110
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED F                         4.6MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1101
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED E                         4.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 1100
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED D                         4.0MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 0011
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED C                         3.7MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 0010
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED B                         3.5MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 0001  
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "SPEED A                         3.3MB/S"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 0000  
		PORT=170h-177h
		IRQ=15
		    SHARE=NO
		    TRIGGER=EDGE

	CHOICE = "DISABLED"
	   LINK
		INIT = IOPORT(1) LOC(7-4) 0000  

FUNCTION="DTC2290 BIOS Memory   W3-CLOSED"
	TYPE="MEM"
	HELP="
Use this option only to verify\n 
resource conflicts.  Actual address\n
selection is performed with on-\n
board jumpers W1, W2 and W3 only."

	CHOICE="C8000-CBFFF   W1-OPENED W2-OPENED (PRIMARY)"
	    FREE
	    MEMORY=14K
		ADDRESS=0C8000h
		WRITABLE=NO
		MEMTYPE=SYS
		CACHE=YES
		SHARE=NO
		SIZE=BYTE
		DECODE=20
	    MEMORY=2K
		ADDRESS=0CB800h
		WRITABLE=YES
		MEMTYPE=SYS
		CACHE=NO
		SHARE=NO
		SIZE=BYTE
		DECODE=20
	   INIT=JUMPER(1) LOC(3 2 1) 100

	CHOICE="D4000-D7FFF   W1-CLOSED W2-CLOSED (PRIMARY)"
	    FREE
	    MEMORY=14K
		ADDRESS=0D4000h
		WRITABLE=NO
		MEMTYPE=SYS
		CACHE=YES
		SHARE=NO
		SIZE=BYTE
		DECODE=20
	    MEMORY=2K
		ADDRESS=0D7800h
		WRITABLE=YES
		MEMTYPE=SYS
		CACHE=NO
		SHARE=NO
		SIZE=BYTE
		DECODE=20
	   INIT=JUMPER(1) LOC(3 2 1) 111

	CHOICE="D0000-D3FFF   W1-OPENED W2-CLOSED (SECONDARY)"
	    FREE
	    MEMORY=14K
		ADDRESS=0D0000h
		WRITABLE=NO
		MEMTYPE=SYS
		CACHE=YES
		SHARE=NO
		SIZE=BYTE
		DECODE=20
	    MEMORY=2K
		ADDRESS=0D3800h
		WRITABLE=YES
		MEMTYPE=SYS
		CACHE=NO
		SHARE=NO
		SIZE=BYTE
		DECODE=20
	   INIT=JUMPER(1)LOC(3 2 1) 101

	CHOICE="D8000-DBFFF   W1-CLOSED W2-OPENED (SECONDARY)"
	    FREE
	    MEMORY=14K
		ADDRESS=0D8000h
		WRITABLE=NO
		MEMTYPE=SYS
		SHARE=NO
		SIZE=BYTE
		DECODE=20
	    MEMORY=2K
		ADDRESS=0DB800h
		WRITABLE=YES
		MEMTYPE=SYS
		SHARE=NO
		SIZE=BYTE
		DECODE=20
	   INIT=JUMPER(1) LOC(3 2 1) 110

FUNCTION="DTC2290 Floppy Controller"
	TYPE="MSD"
;Use this option only to verify\n
;resource conflicts.  The floppy\n
; controller is automatically\n
;   enabled when a drive is\n
;attached to the J1 connector."

      SUBFUNCTION = "Extra High Density Floppy As Drive A:"

      COMMENTS = "The DTC2290 supports the 2.88 Mb Floppy Disk 
		Drives now available. It is necessary to enable 
		this support for each of these drives attached 
		to the DTC2290. To select the 2.88 MByte support 
		for drive A:, the CMOS setup of the floppy drive 
		A: must be set to 3.5 inches 1.44 Mb type, set the
		jumper W9 besides choosing enable in this selection."

        HELP="This Functional area controls the allocation of drive type for
	      EHD Floppy as Drive A: on the Disk Drive Controller Board.
	      If there is a 2.88 floppy drives attached\n
	      to one port, you must enable drive for that port\n
	      and set the jumper W9 for drive A:."

	CHOICE = "Disable"
;       SUBTYPE="CMOS=100F00,CMOS=143E00"
	DISABLE = YES

	CHOICE = "Enable"
;	CHOICE = "5 1/4   360K Floppy Present"
;       SUBTYPE="CMOS=100F10,CMOS=143E01"

;	CHOICE = "5 1/4   1.2M Floppy Present"
;       SUBTYPE="CMOS=100F20,CMOS=143E01"

;	CHOICE = "3 1/2   720K Floppy Present"
;       SUBTYPE="CMOS=100F30,CMOS=143E01"

;	CHOICE = "3 1/2   1.44M Floppy Present"
;       SUBTYPE="CMOS=100F40,CMOS=143E01"

;	CHOICE = "3 1/2   2.88M Floppy Present"
;       SUBTYPE="CMOS=100F40,CMOS=143E01"
	    LINK
		INIT = JUMPER(2) LOC(5) 1
;		PORT=3F0h-3F5h
;		PORT=3F6h-3F7h
;		IRQ=6

      SUBFUNCTION = "Extra High Density Floppy As Drive B:"

      COMMENTS = "The DTC2290 supports the 2.88 Mb Floppy Disk 
		Drives now available. It is necessary to enable 
		this support for each of these drives attached 
		to the DTC2290. To select the 2.88 MByte support 
		for drive B:, the CMOS setup of the floppy drive 
		A: must be set to 3.5 inches 1.44 Mb type, set the 
		jumper W10 besides choosing enable in this selection."

	HELP="This Functional area controls the allocation of drive type for
	      EHD Floppy as Drive B: on the Disk Drive Controller Board.
	      If there is a 2.88 floppy drives attached\n
	      to one port, you must enable EHD floppy drive for that port\n
	      and set the jumper W10 for drive B:."

	CHOICE = "Disable"
	DISABLE = YES

	CHOICE = "Enable"

;	CHOICE = "No Floppy Present "
;       SUBTYPE="CMOS=10F000"

;	CHOICE = "5 1/4   360K Floppy Present"
;       SUBTYPE="CMOS=10F001,CMOS=143E41"

;	CHOICE = "5 1/4   1.2M Floppy Present"
;       SUBTYPE="CMOS=10F002,CMOS=143E41"

;	CHOICE = "3 1/2   720K Floppy Present"
;       SUBTYPE="CMOS=10F003,CMOS=143E41"

;	CHOICE = "3 1/2   1.44M Floppy Present"
;       SUBTYPE="CMOS=100F04,CMOS=143E41"

;	CHOICE = "3 1/2   2.88M Floppy Present"
;       SUBTYPE="CMOS=100F04,CMOS=143E41"
	    LINK
		INIT = JUMPER(2) LOC(6) 1
;		PORT=3F0h-3F5h
;		PORT=3F6h-3F7h
;		IRQ=6

SOFTWARE(1)="DTC2290.SYS -\n
is a DOS driver to get better\n
drive performance.  Place the\n
following command line in\n
     CONFIG.SYS.\n 
\n
device=DTC2290.sys"

SOFTWARE(2)="DTCDISK.SYS -\n
is a DOS driver to access the\n
SECONDARY Port 2.  Place the\n
following command line in\n
CONFIG.SYS after DTC2290.SYS.\n 
\n
device=dtcdisk.sys"

FUNCTION="DTC2290 Floppy Cable Selection (W4)"
	TYPE="MSD"
	HELP="
Use this option only to verify\n 
jumper settings.  Actual\n
operation is selected by jumper\n
installation only."

SUBFUNCTION="DTC2290 Floppy Cable Selection"
	CHOICE="Twisted Ribbon Cable Option   W4-OPENED"
	    LINK
	       INIT=JUMPER(1) LOC(4) 0
	CHOICE="Flat Ribbon Cable Option      W4-CLOSED"
	    LINK
	       INIT=JUMPER(1) LOC(4) 1

FUNCTION="DTC2290 64-HEAD Mapping"
	TYPE="MSD"
	HELP="
Use this option only to verify\n 
jumper settings.  Actual\n
operation is selected by jumper\n
installation only."

SUBFUNCTION="PORT 1 MASTER Drive (W5)"
	CHOICE="Disable 64-HEAD Mapping       W5-OPENED"
	    LINK
	       INIT=JUMPER(2) LOC(1) 0
	CHOICE="Enable 64-HEAD Mapping        W5-CLOSED"
	    LINK
	       INIT=JUMPER(2) LOC(1) 1

SUBFUNCTION="PORT 1 SLAVE Drive (W6)"
	CHOICE="Disable 64-HEAD Mapping       W6-OPENED"
	    LINK
	       INIT=JUMPER(2) LOC(2) 0
	CHOICE="Enable 64-HEAD Mapping        W6-CLOSED"
	    LINK
	       INIT=JUMPER(2) LOC(2) 1

SUBFUNCTION="PORT 2 MASTER Drive (W7)"
	CHOICE="Disable 64-HEAD Mapping       W7-OPENED"
	    LINK
	       INIT=JUMPER(2) LOC(3) 0
	CHOICE="Enable 64-HEAD Mapping        W7-CLOSED"
	    LINK
	       INIT=JUMPER(2) LOC(3) 1

SUBFUNCTION="PORT 2 SLAVE Drive (W8)"
	CHOICE="Disable 64-HEAD Mapping       W8-OPENED"
	    LINK
	       INIT=JUMPER(2) LOC(4) 0
	CHOICE="Enable 64-HEAD Mapping        W8-CLOSED"
	    LINK
	       INIT=JUMPER(2) LOC(4) 1

;;;;;;;;;;;End of Configuration file;;;;;;;;;;;;;;;;