;------------------------------------------------------
;   file name = !DTC0110.CFG, last changed 03-12-90
;------------------------------------------------------
BOARD
   ID = "DTC0110"
   NAME = "DTC6290-24 EISA Disk Controller"
   MFR = "Data Technology"
   CATEGORY = "MSD"
   SLOT = EISA
   LENGTH = 340
   SKIRT = NO
   READID = YES
   BUSMASTER = 400
   AMPERAGE = 4000
   DISABLE = SUPPORTED
   IOCHECK = VALID

   COMMENTS = "
 DTC6290-24 is a high performance EISA disk controller.\n
The features of this board are:\n
- Fully EISA Compatible\n
- Supports Bus Master Mode\n
- Supports Burst Data Transfers\n
- Supports up to 24 MB/sec drives\n
- 33Mbytes/sec Data Transfer Rate\n
- Supports Multi-tasking\n
- Controls up to 4 ESDI Disk Drives\n
- Controls up to 3 Floppy Disk Drives\n
- On-Board Cache 1/2MB to 4MB"

IOPORT(1) = 0ZC85h
   INITVAL = LOC(7-0) 0xxxxxxx

IOPORT(2) = 0ZC84h
   INITVAL = LOC(7-0) 00000xxx


SWITCH(1) = 8
  NAME = "SW1"
  STYPE = DIP
  VERTICAL = NO	
  REVERSE = YES	
  FACTORY = LOC(8-1) 00000000
  INITVAL = LOC(8-1) xxxxx000

  COMMENTS = " \n
*  SW1-1         : Reserved\n
*  SW1-2         : Reserved\n
*  SW1-3         : Reserved\n
*\n
*  SW1-4  OPEN   : One Defect Cylinder\n
*         CLOSED : Two Defect Cylinder\n
*\n
*  SW1-5         : Reserved\n
*\n
*  SW1-6  OPEN   : Floppy Enable\n
*         CLOSED : Floppy Disable\n
*\n
*  SW1-7  OPEN   : Unrestriced Access Mode\n
*         CLOSED : Restricted Access Mode\n
*\n
*  SW1-8  OPEN   : Primary Port Address\n
*         CLOSED : Secondary Port Address\n"

JUMPER(1) = 1
  NAME = "W1"
  JTYPE = INLINE
  VERTICAL = NO	
  REVERSE = YES	
  LABEL = LOC(1^2) "W1"
  INITVAL = LOC(1^2) x

  COMMENTS = " \n
****************************************\n
* This is not a user definable option. *\n
* Do not change factory setting.       *\n
****************************************"

JUMPER(2) = 1
  NAME = "W2"
  JTYPE = INLINE
  VERTICAL = NO	
  REVERSE = YES	
  LABEL = LOC(1^2) "W2"
  INITVAL = LOC(1^2) x

  COMMENTS = " \n
****************************************\n
* This is not a user definable option. *\n
* Do not change factory setting.       *\n
****************************************"

FUNCTION = "Floppy Subsystem"
  TYPE = "MSD"

  COMMENTS = "
 The floppy drives that use standard logic can be\n
configured as DRIVES 1-3.  Drives that require reverse\n
logic (PS/2 type drives) can only be configured as\n
DRIVE 2.\n
\n
When standard AT type floppy disk drives are connected\n
to the DTC6290-24, select Standard Logic.  When connecting\n
a PS/2 type floppy disk drive, select Reverse Logic.  If\n
the floppy is disabled (SW1-6 is CLOSED), select Disable\n
Floppy Controller.  The default setting is Standard Logic."

  CHOICE = "Standard Logic"
    FREE
      DMA = 2
    LINK
      IRQ = 6
      INIT = SWITCH(1) LOC(6) 0
      INIT = IOPORT(1) LOC(0) 0
    LINK
      PORT = 03F2H-03F7H | 0372H-0377H
      INIT = SWITCH(1) LOC(8) 0 | 1
  CHOICE = "Reverse Logic"
    FREE
      DMA = 2
    LINK
      IRQ = 6
      INIT = SWITCH(1) LOC(6) 0
      INIT = IOPORT(1) LOC(0) 1
    LINK
      PORT = 03F2H-03F7H | 0372H-0377H
      INIT = SWITCH(1) LOC(8) 0 | 1
  CHOICE = "Disable Floppy Controller"
    DISABLE = YES
    LINK
      INIT = SWITCH(1) LOC(6) 1

FUNCTION = "ESDI Subsystem"
  TYPE = "MSD"

  SUBFUNCTION = "Access Mode"

    COMMENTS = "
 This switch controls the accessibility to the ISA hard disk\n
and floppy disk registers.  Most users should select\n
Unrestricted Access Mode.  The mode defined by this utility\n
must match the mode defined by the hardware switch SW1-7.\n
The default is Unrestricted Access Mode.\n"

    CHOICE = "Unrestricted Access Mode"
      LINK
        INIT = SWITCH(1) LOC(7) 0
        INIT = IOPORT(2) LOC(0) 1
    CHOICE = "Restricted Access Mode"
      LINK
        INIT = SWITCH(1) LOC(7) 1
        INIT = IOPORT(2) LOC(0) 1


  SUBFUNCTION = "I/O Port Address"

    COMMENTS = "
 This setting selects the I/O port address for the hard disk\n
and floppy disk registers.  The default setting is Primary\n
Port.\n
\n
Primary Port   = 1F0H-1F7H\n
Secondary Port = 170H-177H"

    CHOICE = "Primary Port"
      LINK
        INIT = SWITCH(1) LOC(8) 0
        PORT = 01F0H-01F7H
    CHOICE = "Secondary Port"
      LINK
        INIT = SWITCH(1) LOC(8) 1
        PORT = 0170H-0177H

  SUBFUNCTION = "Interrupt Request"

    COMMENTS = "
 You can select either IRQ 14 or IRQ 15 for the ESDI hard\n
disk controller interrupt.  The default is IRQ 14.\n"

    CHOICE = "IRQ 14"
      LINK
        INIT = IOPORT(1) LOC(6) 0
        IRQ =  14
          SHARE = NO
          TRIGGER = EDGE
    CHOICE = "IRQ 15"
      LINK
        INIT = IOPORT(1) LOC(6) 1
        IRQ = 15
         SHARE = NO
         TRIGGER = EDGE

  SUBFUNCTION = "Auto-Deselect Mode"

    COMMENTS = "
 The Auto-Deselect mode affects the drive activity LED.\n
When Enabled, the hard disk drives will only be selected\n
during command execution.  When Disabled, one drive will\n
be selectd at all times.  The default is Enabled.\n"

    CHOICE = "Enable"
      LINK
        INIT = IOPORT(1) LOC(5) 1
        INIT = IOPORT(1) LOC(4) 1
    CHOICE = "Disable"
      LINK
        INIT = IOPORT(1) LOC(5) 0
        INIT = IOPORT(1) LOC(4) 1