BOARD 
 ID="DBT0002"
 NAME="NEC Multi-8 Board"
 MFR="NEC"
 CATEGORY="COM"
 SLOT=ISA16    
 COMMENTS="
 \nThe NEC Multi-8 Board requires the use of a device driver
 appropriate to your operating system. Each of the supported 
 operating systems has recommended parameter values. Refer to 
 documentation for these values and for further information."

HELP=" Use the V)iew D)etail by Slot mode to see Configuration
 Options. Use E)dit Change R)esources to select parameters."

SWITCH (1)=8
 NAME="S1"
 STYPE=DIP
 VERTICAL=NO
 REVERSE=YES
 LABEL=LOC(1-8) "SW1" "SW2" "SW3" "SW4" "SW5" "SW6" "SW7" "SW8" 
 FACTORY = LOC(1-8) 10001111
 COMMENTS = "Dual-Ported Memory Starting Address Selection"
SWITCH (2)=8
 NAME="S2"
 STYPE=DIP
 VERTICAL=NO
 REVERSE=YES
 LABEL=LOC(1-8) "SW1" "SW2" "SW3" "SW4" "SW5" "SW6" "SW7" "SW8"
 FACTORY = LOC(1-8) 11111111
 COMMENTS="SW1:  Selects Bank One Size(DRAM installed: On = 128K*, Off = 512K)\n
	SW2:  Selects Bank One Empty(On = No DRAM*, Off = DRAM Present)\n
	SW3, SW4, SW5:  Select I/O Port Address\n
	SW6:  Selects EPROM(On = No EPROM*, Off = EPROM present)\n
	SW7, SW8:  EPROM Size (Off/Off = 16KB,On/On = 128KB*)\n
	* Default Setting"
SWITCH (3)=8
 NAME="S3"
 STYPE=DIP
 VERTICAL=NO
 REVERSE=YES
 LABEL=LOC(1-8) "SW1" "SW2" "SW3" "SW4" "SW5" "SW6" "SW7" "SW8"
 FACTORY = LOC(1-8) 00001000
 COMMENTS = "Interrupt Address Settings"
JUMPER(1) = 1
 NAME ="J1 - Clock Source"
 JTYPE = TRIPOLE
 VERTICAL = NO
 REVERSE = YES
 INITVAL = LOC(1) 1
 LABEL = LOC(1) "1-2-3"
 COMMENTS = "Jumper on 1-2 selects the clock source for the 8530.  This is
		the default setting."	
JUMPER(2) = 1
 NAME ="J6 - SRAM Indicator"
 JTYPE = TRIPOLE
 VERTICAL = YES
 REVERSE = NO
 INITVAL = LOC(1) 0
 LABEL = LOC(1) "1-2-3"
 COMMENTS = "Jumper on 1-2 indicates the presence of SRAM on board.  This is
		the default setting."
SOFTWARE(1) ="
 The DigiBoard DigiCHANNEL board requires the installation of a device
 driver appropriate to your operating system. Refer to the
 DigiBoard documentation for details and configure using the following
 parameters:\n"

FUNCTION="Multiport Communications"
 TYPE="COM"
 COMMENTS = "Option 5:  This option shows the resources required for all four 
	boards listed above, but it does not display the switch and jumper 
	settings for each board.  See individual options for those settings.\n\n
	Option 6:  For more memory settings, see the Installation Manual.\n"
 HELP="Use E)dit Change F)unction to Select Options.
 \n\nSelect the Desired Operating System to Obtain Selection of
 Valid Option Choices."

 CHOICE="Option 1 - Single Board"

FREE
	MEMORY = 64K
	ADDRESS = 0E0000H
	MEMTYPE = OTH
	INIT = SWITCH(1) LOC(1-8) 10001111
FREE ;LINK
	IRQ = 10
	PORT = 320h
	INIT = SWITCH(2) LOC(1-8) 11111111
	INIT = SWITCH(3) LOC(1-8) 00001000

 CHOICE="Option 2 - Single Board"

LINK
	MEMORY = 64K
	ADDRESS = 0D0000H
	MEMTYPE = OTH
	INIT = SWITCH(1) LOC(1-8) 01001111
LINK
	IRQ = 11
	PORT = 300h
	INIT = SWITCH(2) LOC(1-8) 11110100
	INIT = SWITCH(3) LOC(1-8) 00000100

CHOICE="Option 3 - Single Board"

LINK
	MEMORY = 64K
	ADDRESS = 0E00000h
	MEMTYPE = OTH
	INIT = SWITCH(1) LOC(1-8) 11111000
LINK
	IRQ = 12
	PORT = 220h
	INIT = SWITCH(2) LOC(1-8) 11101100
	INIT = SWITCH(3) LOC(1-8) 00000010

CHOICE="Option 4 - Single Board"

LINK
	MEMORY = 64K
	ADDRESS = 0D80000h
	MEMTYPE = OTH
	INIT = SWITCH(1) LOC(1-8) 11100100
LINK
	IRQ = 15
	PORT = 120h
	INIT = SWITCH(2) LOC(1-8) 11011100
	INIT = SWITCH(3) LOC(1-8) 00000001

CHOICE = "Option 5 - 4 Boards"
HELP = "This option shows the resources required for all four boards, but 
	it does not display the switch and jumper settings for each board.
	See individual options for those settings.\n"
LINK
	IRQ = 10
	IRQ = 11
	IRQ = 12
	IRQ = 15
	PORT = 120h
	PORT = 220h
	PORT = 300h
	PORT = 320h
LINK
	MEMORY = 64K
	ADDRESS = 0E0000H
	MEMTYPE = OTH
LINK
	MEMORY = 64K
	ADDRESS = 0D80000h
	MEMTYPE = OTH
LINK
	MEMORY = 64K
	ADDRESS = 0D0000H
	MEMTYPE = OTH
LINK
	MEMORY = 64K
	ADDRESS = 0E00000h
	MEMTYPE = OTH
CHOICE = "Option 6 - Custom Installation"
HELP = "For more memory settings, see the Installation Manual.\n
	In the section on 'Port Addresses' 0h Port selects 'none'"

LINK
	MEMORY = 64K
	ADDRESS = 0E0000h|0E80000h|0E00000h|0D80000h|0C0000h|0D0000h|
		  100000h|200000h|300000h|400000h|500000h|600000h|
		  700000h|800000h|900000h|0A00000h|0B00000h|0C00000h|
		  0D00000h|0F00000h
	  MEMTYPE = OTH
	INIT = SWITCH(1)LOC(1-8)
		10001111|11101000|11111000|11100100|11001111|01001111|
		11110111|11111011|11110011|11111101|11110101|11111001|
		11110001|11111110|11110110|11111010|11110010|11111100|
		11110100|11110000

LINK
	PORT =	320h|300h|220|200h|120h|110h|100h
	INIT = SWITCH(2)LOC(1-8)
		11111111|11110100|11101100|11100100|11011100|11010100|11001100

LINK
	IRQ = 10|3|4|5|7|11|12|15
	INIT = SWITCH(3)LOC(1-8)
		00001000|10000000|01000000|00100000|00010000|00000100|
		00000010|00000001