; EISA Configuration File for Computone IntelliPort-IIEX EISA-CEX ; Revision History: ; 5/26/92 MAG First Draft ; 12/15/93 MAG PORTVAR removed, ; Config Disk's Version number added to HELP ; Order of Interrupt selections changed. BOARD ID = "CTN0281" NAME = "IntelliPort-IIEX (EISA-CEX)" MFR = "Computone Corporation" CATEGORY = "COM" AMPERAGE = 1000 SLOT = EISA LENGTH = 200 SKIRT = NO READID = YES IOCHECK = INVALID DISABLE = SUPPORTED COMMENTS = "The Computone IntelliPort-IIEX consists of a controller card, the EISA-CEX, connected to up to four expansion boxes, using either the EX-16DB (16-port) or EX-8DB (8-port) boxes. This allows up to 64 asynchronous ports per card to be supported. \n The expansion boxes are normally powered from the system, but should power requirements exceed your power supply ratings, a power adapter module is available to supply power to the expansion boxes.\n This board uses only EISA slot-dependent i/o addresses, and an interrupt which is automatically configured." HELP = "Option/Configuration Disk, Version 2.06\n Select IRQ. The i/o address depends on the slot you have chosen." IOPORT(1) = 0ZC86h SOFTWARE(1) = "Drivers are available to support:\n SCO Xenix and Unix\n AT&T / Interactive Unix (3.2)\n UNIX System V release 4\n The drivers are supplied on separate diskette. Refer to our manual as well as the manuals for your o/s for driver installation information.\n Please make note which interrupt and slot you have selected; you may need this during driver installation." FUNCTION = "Computone IntelliPort-IIEX (EISA-CEX)" CONNECTION = "Uses DB37 Recepticle to connect to expansion boxes. Boxes feature female DB25 connectors.\n Signals:\n TxD, RxD, DTR, DCD, CTS, RTS, DSR, RI" TYPE = "COM" SUBFUNCTION = "Interrupt" COMMENTS= "Select the irq this board is to use. Record your selection; you will need to provide this information when installing software drivers.\n For more details, select [help]." HELP= "This utility will configure the board to use the interrupt that you select, but the software drivers may also need to know this.\n When installing multiple IntelliPort-II boards, use the same interrupt for all. (Exception: ISA IntelliPort-II boards cannot share an interrupt with EISA IntelliPort-II boards.) Not all drivers will support polled (non-interrupt) operation." CHOICE = "IRQ10" LINK IRQ = 10 SHARE = "CTN.EII" TRIGGER = LEVEL INIT = IOPORT(1) 00001100b CHOICE = "IRQ11" LINK IRQ = 11 SHARE = "CTN.EII" TRIGGER = LEVEL INIT = IOPORT(1) 00001101b CHOICE = "IRQ12" LINK IRQ = 12 SHARE = "CTN.EII" TRIGGER = LEVEL INIT = IOPORT(1) 00001110b CHOICE = "IRQ15" LINK IRQ = 15 SHARE = "CTN.EII" TRIGGER = LEVEL INIT = IOPORT(1) 00001111b CHOICE = "IRQ3" LINK IRQ = 3 SHARE = "CTN.EII" TRIGGER = LEVEL INIT = IOPORT(1) 00001000b CHOICE = "IRQ4" LINK IRQ = 4 SHARE = "CTN.EII" TRIGGER = LEVEL INIT = IOPORT(1) 00001001b CHOICE = "IRQ5" LINK IRQ = 5 SHARE = "CTN.EII" TRIGGER = LEVEL INIT = IOPORT(1) 00001010b CHOICE = "IRQ7" LINK IRQ = 7 SHARE = "CTN.EII" TRIGGER = LEVEL INIT = IOPORT(1) 00001011b CHOICE = "Polled (No interrupt used)" LINK INIT = IOPORT(1) 00000000b SUBFUNCTION = "Expansion Box Configuration" COMMENTS= "This selection helps the configuration utility determine whether the power supply has enough +5 volt current to support all the expansion boxes. If not, you should also install our external power source, the EX-PAM. \n WARNING: The configuration utility does not validate +12 and -12 volt requirements. The amount of 12-volt current needed depends strongly on what RS232 devices are connected. If a large number of devices are being used, you may wish to use the EX-PAM even if no +5 volt problem is detected." CHOICE = "EX-PAM supplies power to boxes." AMPERAGE = 10 ; milliamps LINK INIT = SOFTWARE(1) "Must use EX-PAM" CHOICE = "One Expansion Box, No EX-PAM" AMPERAGE = 490 ; (assuming 16-port size) CHOICE = "Two Expansion Boxes, No EX-PAM" AMPERAGE = 980 CHOICE = "Three Expansion Boxes, No EX-PAM" AMPERAGE = 1470 CHOICE = "Four Expansion Boxes, No EX-PAM" AMPERAGE = 1960