FUNCTION="Software error recovery boot option"
 HELP="Use the arrow keys to select the boot option when a software ASR
 reset occurs.  Select 'Boot operating system' to quickly restore
 the server after an ASR reset.  Select 'Boot Compaq Utilities' to
 help diagnose the cause of the ASR reset and to remotely
 diagnose the ASR error."
 RESOURCE="ASRBOOT1",UNIQUE
 RESOURCE="ASRBOOT2",UNIQUE
  CHOICE="Boot operating system"
   LINK
   MEMBER="ASRBOOT1","0"
   SHARE=NO
   MEMBER="ASRBOOT2","0"
   SHARE=NO
  CHOICE="Boot Compaq Utilities"

 FUNCTION="Thermal shutdown"
 HELP="If Thermal Reset is enabled, the O/S will shutdown the system if
 the temperature exceeds specifications."
  CHOICE="Enabled"
  CHOICE="Disabled"

 FUNCTION="UPS shutdown"
 HELP="If enabled, the O/S will shutdown the system after it
 detects an A/C power failure. "
   CHOICE="Enabled"
   CHOICE="Disabled"

 FUNCTION="UPS shutdown threshold"
 HELP="Begin orderly O/S shutdown when UPS battery reserve is less than UPS
 shutdown threshold."
   CHOICE="5 minutes"
   CHOICE="1 minutes"
   CHOICE="2 minutes"
   CHOICE="3 minutes"
   CHOICE="4 minutes"
   CHOICE="6 minutes"
   CHOICE="7 minutes"
   CHOICE="8 minutes"
   CHOICE="9 minutes"
   CHOICE="10 minutes"
   CHOICE="11 minutes"
   CHOICE="12 minutes"
   CHOICE="13 minutes"
   CHOICE="14 minutes"
   CHOICE="15 minutes"
   CHOICE="16 minutes"
   CHOICE="17 minutes"
   CHOICE="18 minutes"
   CHOICE="19 minutes"
   CHOICE="20 minutes"
   CHOICE="21 minutes"
   CHOICE="22 minutes"
   CHOICE="23 minutes"
   CHOICE="24 minutes"
   CHOICE="25 minutes"
   CHOICE="26 minutes"
   CHOICE="27 minutes"
   CHOICE="28 minutes"
   CHOICE="29 minutes"
   CHOICE="30 minutes"

ENDGROUP

GROUP="Server Failure Notification"

 FUNCTION="Pager status"
 HELP="If enabled, the pager dial string and pager message (if present)
 will be dialed after an ASR reset."
  CHOICE="Disabled"
  CHOICE="Enabled"
   LINK
   MEMBER="ASRSTAT1","0"
   SHARE=NO

 FUNCTION="Pager dial string"
 HELP="Enter the dial string followed by the pager's telephone number.
 This number will be dialed when an ASR reset occurs if the Pager status
 is set to 'Enabled'.\n\n
 The following dial modifiers can be used with Hayes(TM)
 compatible modems:\n
 T\tUse tone dialing\n
 P\tUse pulse dialing\n
 ,\tPause two seconds\n
 W\tWait for second dial tone\n
 @\tWait for a ring followed by five\n
 \tor more seconds of silence\n
 !\tFlash\n
 ;\tReturns the modem to the command\n
 \tstate\n
 S=n\tDials a number stored in a dial\n
 \tstring\n
 R\tNormal dial\n\n
 Refer to your modem's documentation for more information on
 the commands used by your modem."
  CHOICE=""

 FUNCTION="Pager message"
 HELP="Enter a message that uniquely identifies this computer.
 This optional message will be sent to the pager after the pager
 dial string has been dialed to indicate which machine reset.  Most pager
 services require the '#' character to follow the message.  If no
 message is required, delete the '#'.  The Pager dial string and
 message are only dialed when Pager status is set to 'Enabled'."
  CHOICE=""

 FUNCTION="Pager test"
 HELP="Select this function and press ENTER to send the
 current Pager dial string and Pager message to the modem at
 the selected serial interface.  Use this feature to
 ensure that Server Failure Notification is configured
 for your pager service."
  CHOICE="Select to test pager setup"

ENDGROUP

GROUP="Remote Options"

 FUNCTION="Serial interface"
 HELP="Use the arrow keys to select the communications port
 for the modem used by ASR."
 COMMENTS="\nSelect the communications port for the modem used by the Server
 Failure Notification and Remote Options."

  CHOICE="COM2"
  CHOICE="COM1"

 FUNCTION="Dial in status"
 HELP="If enabled, the modem will be set to automatically answer
 incoming calls.  You will then be able to call the server using
 a terminal emulator set for 8 data bits, 1 stop bit, and no parity
 and remotely run the Compaq Utilities.  If Dial out status is
 enabled but no connection is made after 5 attempts, the modem
 will be set to answer incoming calls."
 RESOURCE="ASRREMOTE",UNIQUE
  CHOICE="Disabled"
   LINK
   MEMBER="ASRREMOTE","0"
   SHARE=NO
  CHOICE="Enabled"
   LINK
   MEMBER="ASRSTAT3","0"
   SHARE=NO
   MEMBER="ASRBOOT2","0"
   SHARE=NO

 FUNCTION="Dial out status"
 HELP="If enabled, the dial out string will be dialed after an ASR reset
 when the server boots to the Compaq Utilities.  If unable to connect
 after 5 attempts, the modem will be put in auto answer mode regardless
 of the Dial in status."
  CHOICE="Disabled"
  CHOICE="Enabled"
   LINK
   MEMBER="ASRSTAT2","0"
   SHARE=NO
   MEMBER="ASRBOOT1","0"
   SHARE=NO
   MEMBER="ASRREMOTE","0"
   SHARE=NO

 FUNCTION="Dial out string"
 HELP="Enter the dial string followed by the remote computer's
 telephone number.  This number will be dialed when an ASR reset
 occurs if the Dial out status is set to 'Enabled'.\n\n
 The following dial modifiers can be used with Hayes(TM)
 compatible modems:\n
 T\tUse tone dialing\n
 P\tUse pulse dialing\n
 ,\tPause two seconds\n
 W\tWait for second dial tone\n
 @\tWait for a ring followed by five\n
 \tor more seconds of silence\n
 !\tFlash\n
 ;\tReturns the modem to the command\n
 \tstate\n
 S=n\tDials a number stored in a dial\n
 \tstring\n
 R\tNormal dial\n\n
 Refer to your modem's documentation for more information on
 the commands used by your modem."
  CHOICE=""

 FUNCTION="Network status"
 HELP="If enabled, Remote will allow you to connect via the network."
   CHOICE="Disabled"
   CHOICE="Enabled"

 FUNCTION="Network controller"
 HELP="If you chose Custom, you will need to create the NET.CFG file and move
 it and any required driver file to the system partition."
   CHOICE="NetFlex"
   CHOICE="Custom"

 FUNCTION="Network host name"
 HELP="The Host name is the name by which the Server will be identified on the
 Network."
   CHOICE=""

 FUNCTION="Network card slot"
 HELP="The NETFLEX board is the only board supported for this feature. Other
 boards may be used but will require that you select Custom controller, create
 the NET.CFG file yourself and copy it to the System Partition."
   CHOICE=""

 FUNCTION="Network Frame Type"
 HELP="The default is ETHERNET_802.3. See you network documentation for more
 description concerning frame types."
   CHOICE="ETHERNET_802.3 "
   CHOICE="ETHERNET_802.2 "
   CHOICE="ETHERNET_II    "
   CHOICE="ETHERNET_SNAP  "
   CHOICE="TOKEN-RING     "
   CHOICE="TOKEN-RING_SNAP"


 FUNCTION="" SHOW=NO CHOICE=""
 FUNCTION="" SHOW=NO CHOICE=""

ENDGROUP