; eMASTER+ EISA FDE (32-Bit BURST-MODE LAN ADAPTER, Full-Duplex) ; Cogent Data Technologies, Inc. 1993 ; Board Number 945001-00 ; Version 1.03 (940711) ; ;--------------------------------- ; Revision History ;--------------------------------- ; 1.00 Initial release ; 1.01 10/7/93 Linked read and write bursting ; 1.02 3/16/94 Latch shared interrupts ; 1.03 7/11/94 Default to Non-Burst ; BOARD ID = "COG9005" ; Product ID. NAME = "Cogent eMASTER+ EISA FDE 32-Bit Burst-mode Ethernet Adapter" MFR = "Cogent Data Technologies, Inc." CATEGORY = "NET" ; Category, i.e. Network Board. SLOT = EISA ; Uses EISA Slot. LENGTH = 216 ; Length of Board in Millimeters. READID = YES ; Board ID can be read BUSMASTER = 40 ; Bus latency time allowed AMPERAGE = 1000 ; IOCHECK = INVALID ; No IOCHKERR bit. DISABLE = SUPPORTED ; Disabled by clearing ; the control register ENABLE bit. COMMENTS = " The Cogent eMASTER+ EISA FDE is a 32-bit 596 Ethernet Adapter for the EISA bus, capable of supporting Full-Duplex communications." HELP = "The Cogent eMASTER+ EISA FDE is a 32-bit bus-mastering ethernet adapter. This configuration process will help you select the IRQ and Ethernet cable type used by the eMASTER+." IOPORT(1) = 0zc88h INITVAL = 1100xxxx ;32 bit data size ;bus release after 23 BCLKs IOPORT(2) = 0zc89h INITVAL = 0000xxxx ;slot specific I/O only IOPORT(3) = 0zc8Ah INITVAL = LOC(7-6) 00 ;No Boot ROM IOPORT(4) = 0zc8Fh INITVAL = 0x000x00 ;immediate bus release ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; SOFTWARE(1) = "The Cogent eMASTER+ EISA FDE has \n \tODI drivers for NetWare 386 servers and workstations.\n \tNDIS drivers for DOS, OS/2 and VINES.\n \tLLI Streams drivers for UNIX.\n A diagnostic (EMSETUP) is supplied for testing." ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; GROUP = "Interrupt Selection" ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; FUNCTION = "eMASTER+ IRQ Number" COMMENTS = "The eMASTER+ EISA FDE allows unshared (edge-triggered) or shared (level-triggered) interrupts. Select an interrupt number and IRQ sharing option for the eMASTER+ EISA FDE to use." HELP = "Shared interrupts may be used to allow multiple eMASTER+ EISA adapters to share the same interrupt. Cogent does not recommend sharing interrupts with other types of adapters.\n Unshared interrupts should be used if your EISA system cannot support shared interrupts or if only a single eMASTER+ will be used in your system." CHOICE = "IRQ 5, trigger:edge, unshared" SUBTYPE = "IRQ5" LINK IRQ = 5 TRIGGER = EDGE SHARE = NO INIT = IOPORT(1) LOC(3-0) 0001 CHOICE = "IRQ 10, trigger:edge, unshared" SUBTYPE = "IRQA" LINK IRQ = 10 TRIGGER = EDGE SHARE = NO INIT = IOPORT(1) LOC(3-0) 0101 CHOICE = "IRQ 11, trigger:edge, unshared" SUBTYPE = "IRQB" LINK IRQ = 11 TRIGGER = EDGE SHARE = NO INIT = IOPORT(1) LOC(3-0) 0111 CHOICE = "IRQ 12, trigger:edge, unshared" SUBTYPE = "IRQC" LINK IRQ = 12 TRIGGER = EDGE SHARE = NO INIT = IOPORT(1) LOC(3-0) 0011 CHOICE = "IRQ 5, trigger:level, shared" SUBTYPE = "IRQ5" LINK IRQ = 5 TRIGGER = LEVEL SHARE = YES INIT = IOPORT(1) LOC(3-0) 1000 CHOICE = "IRQ 10, trigger:level, shared" SUBTYPE = "IRQA" LINK IRQ = 10 TRIGGER = LEVEL SHARE = YES INIT = IOPORT(1) LOC(3-0) 1100 CHOICE = "IRQ 11, trigger:level, shared" SUBTYPE = "IRQB" LINK IRQ = 11 TRIGGER = LEVEL SHARE = YES INIT = IOPORT(1) LOC(3-0) 1110 CHOICE = "IRQ 12, trigger:level, shared" SUBTYPE = "IRQC" LINK IRQ = 12 TRIGGER = LEVEL SHARE = YES INIT = IOPORT(1) LOC(3-0) 1010 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ENDGROUP ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; GROUP = "Ethernet Cable Selection" ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; FUNCTION = "eMASTER+ Connector" COMMENTS = "The eMASTER+ EISA FDE provides connectors for all three cable types: Thin, Thick, and Twisted-Pair. Select the connector and cable type that you will be using. Full-Duplex is available only for 10BASE-T connections and should only be used when connected directly to a switch or hub that supports Full-Duplex operation." HELP = "none available" CONNECTION = "\tuse BOTTOM connector (BNC) for THIN cable\n \tuse MIDDLE connector (AUI) for THICK cable\n \tuse TOP connector (RJ-45) for TWISTED-PAIR cable" CHOICE = "Unshielded Twisted-Pair (10BASE-T), Full-Duplex" FREE INIT = IOPORT(2) LOC(3 1 0) 101 CHOICE = "Unshielded Twisted-Pair (10BASE-T), Half-Duplex" FREE INIT = IOPORT(2) LOC(3 1 0) 011 CHOICE = "Thick Ethernet (10BASE-5)" FREE INIT = IOPORT(2) LOC(3 1 0) 011 CHOICE = "Thin Ethernet (10BASE-2)" FREE INIT = IOPORT(2) LOC(3 1 0) 010 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; FUNCTION = "Twisted-Pair Control" COMMENTS = "Link Integrity is normally enabled; it should be disabled only for compatibility with older network hardware." HELP = "none available" CHOICE = "Link Integrity Enabled" FREE INIT = IOPORT(2) LOC(2) 1 CHOICE = "Link Integrity Disabled" FREE INIT = IOPORT(2) LOC(2) 0 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ENDGROUP ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; FUNCTION = "Bus Master Parameters" HELP = "These parameters fine-tune the Bus-Mastering of the eMASTER+ EISA FDE to your specific system.\n\n Note that differences in performance and even system operation are highly dependent on your particular platform." COMMENTS = "The eMASTER+ EISA FDE fully supports EISA high-speed burst transfers to memory. Most EISA machines support these high-speed transfers; if your machine is unable to use EISA burst-mode, then select the Non-Burst option." CHOICE = "Non-Burst" FREE INIT = IOPORT(4) LOC(6 2) 00 CHOICE = "Burst Enabled" FREE INIT = IOPORT(4) LOC(6 2) 11 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;