; File name = !BUS6301.CFG
; Date : 10/26/92

BOARD
   ID = "BUS6301"               ; EISA 9020DEMO Rev 1 Product ID.
   NAME = "BusLogic EISA 32-Bit 82596 Ethernet Controller (v1.0)"
   MFR = "BusLogic"             ; Manufacturere Name.
   CATEGORY = "NET"             ; Category, i.e. Network Board.
   SLOT = EISA                  ; Uses EISA Slot.
   LENGTH = 216                 ; Length of Board in Millimeters.
   READID = yes                 ; Board ID can be read
   BUSMASTER = 40               ; Bus latency time allowed
   AMPERAGE = 1000              ; Needs to be measured.
   IOCHECK = INVALID            ; Card will not respond to reads of
                                ;  it's IOCHKERR bit.
   DISABLE = SUPPORTED          ; The card can be disabled by clearing
                                ;  the control register ENABLE bit.
   COMMENTS = " The BT-763E Board is a 32 bit 82596 Ethernet Adaptor
                for the EISA bus. The board is a bus master design that
                uses the host system main memory directly. "

   HELP = "No help available."

IOPORT(1) = 0zc88h
  INITVAL = LOC(7-0) 110x0xxx

IOPORT(2) = 0zc89h
  INITVAL = LOC(7-0) 00000x1x

IOPORT(3) = 0zc8Ah
  INITVAL = LOC(7-0) xxxxx000

IOPORT(4) = 0zc8Fh
  INITVAL = LOC(7-0) xxxxxxx0

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

;FUNCTION = "Host I/O Port Addresses"
;   COMMENTS = "This board supports both slot-specific and ISA\n
;                compatible I/O addressing.  The ISA mode should only\n
;                be used for software compatibility with ISA drivers."
;
;      CHOICE = "Slot-Specific Only (Default)"
;        FREE
;        INIT = IOPORT(2) LOC(7-4) 0000
;
;      CHOICE = "Slot-Specific and ISA"
;        LINK
;        INIT = IOPORT(2) LOC(7-4) 0001|0010|0101|0111|1001|1011|1101
;        PORT = 100h-11Fh|120h-13fh|140h-15fh|160h-17fh|300h-31fh|
;               320h-32fh|340h-35fh
;

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

FUNCTION = "BT-763E Ethernet EPROM"
      TYPE = "ROM"
      CHOICE = "EPROM Disabled (Default)"
        FREE
        INIT = IOPORT(3) LOC(7-6) 00

      CHOICE = "0C8000h"
        LINK
        MEMORY = 16K
        ADDRESS = 0C8000H
        WRITABLE = NO
        MEMTYPE = OTHER
        SIZE = BYTE
        INIT = IOPORT(3) LOC(5-3) 010
        INIT = IOPORT(3) LOC(7-6) 10

      CHOICE = "0CC000h"
        LINK
        MEMORY = 16K
        ADDRESS = 0CC000H
        WRITABLE = NO
        MEMTYPE = OTHER
        SIZE = BYTE
        INIT = IOPORT(3) LOC(5-3) 011
        INIT = IOPORT(3) LOC(7-6) 10

      CHOICE = "0D0000h"
        LINK
        MEMORY = 16K
        ADDRESS = 0D0000H
        WRITABLE = NO
        MEMTYPE = OTHER
        SIZE = BYTE
        INIT = IOPORT(3) LOC(5-3) 100
        INIT = IOPORT(3) LOC(7-6) 10

      CHOICE = "0D4000h"
        LINK
        MEMORY = 16K
        ADDRESS = 0D4000H
        WRITABLE = NO
        MEMTYPE = OTHER
        SIZE = BYTE
        INIT = IOPORT(3) LOC(5-3) 101
        INIT = IOPORT(3) LOC(7-6) 10

      CHOICE = "0D8000h"
        LINK
        MEMORY = 16K
        ADDRESS = 0D8000H
        WRITABLE = NO
        MEMTYPE = OTHER
        SIZE = BYTE
        INIT = IOPORT(3) LOC(5-3) 110
        INIT = IOPORT(3) LOC(7-6) 10

      CHOICE = "0DC000h"
        LINK
        MEMORY = 16K
        ADDRESS = 0DC000H
        WRITABLE = NO
        MEMTYPE = OTHER
        SIZE = BYTE
        INIT = IOPORT(3) LOC(5-3) 111
        INIT = IOPORT(3) LOC(7-6) 10

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

FUNCTION = "Link Integrity (for Twisted Pair connection only)"
      CHOICE = "Enable (Default)"
        FREE
        INIT = IOPORT(2) LOC(0) 0

      CHOICE = "Disable"
        FREE
        INIT = IOPORT(2) LOC(0) 1

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

;FUNCTION = "Bus Master"

;   SUBFUNCTION = "Burst/Non-Burst Bus cycles"

FUNCTION = "Burst/Non-Burst Bus Cycles"
      CHOICE = "Non-Burst (Default)"
        FREE
        INIT = IOPORT(4) LOC(2) 0

      CHOICE = "Burst"
        FREE
        INIT = IOPORT(4) LOC(2) 1

;   SUBFUNCTION = "Bus Release After Preempt"
;      CHOICE = "23 BCLK Cycles"
;        FREE
;        INIT = IOPORT(1) LOC(5) 0
;
;      CHOICE = "55 BCLK Cycles"
;        FREE
;        INIT = IOPORT(1) LOC(5) 1
;
;   SUBFUNCTION = "Bus Hold Between Transfers"
;      CHOICE = "Give up bus when done"
;        FREE
;        INIT = IOPORT(4) LOC(0) 0
;
;      CHOICE = "Hold bus for 800 nsec when done"
;        FREE
;        INIT = IOPORT(4) LOC(0) 1

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

FUNCTION = "Thin/Thick Net Selection"
      COMMENTS = " Twisted Pair connection is automatically enabled whenever
                   you connect it, no matter which option you select here."
      TYPE = "NET"
      CHOICE = "Thin Net (Default)"
        LINK
        INIT = IOPORT(2) LOC(2) 1

      CHOICE = "Thick Net"
        LINK
        INIT = IOPORT(2) LOC(2) 0

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

FUNCTION = "Host Interrupt Request"

;   SUBFUNCTION = "Interrupt Channel vs. Edge/Level"
      CHOICE = "INT10 Edge (Default)"
      LINK
        INIT = IOPORT(1) LOC(2-0) 011
        IRQ = 10
         TRIGGER = EDGE
         SHARE = NO

      CHOICE = "INT9 Edge"
      LINK
        INIT = IOPORT(1) LOC(2-0) 001
        IRQ = 9
         TRIGGER = EDGE
         SHARE = NO

      CHOICE = "INT11 Edge"
      LINK
        INIT = IOPORT(1) LOC(2-0) 101
        IRQ = 11
         TRIGGER = EDGE
         SHARE = NO

      CHOICE = "INT15 Edge"
      LINK
        INIT = IOPORT(1) LOC(2-0) 111
        IRQ = 15
         TRIGGER = EDGE
         SHARE = NO

;      CHOICE = "INT9 Level"
;      LINK
;        INIT = IOPORT(1) LOC(2-0) 000
;        IRQ = 9
;         TRIGGER = LEVEL
;         SHARE = NO
;
;      CHOICE = "INT10 Level"
;      LINK
;        INIT = IOPORT(1) LOC(2-0) 010
;        IRQ = 10
;         TRIGGER = LEVEL
;         SHARE = NO
;
;      CHOICE = "INT11 Level"
;      LINK
;        INIT = IOPORT(1) LOC(2-0) 100
;        IRQ = 11
;         TRIGGER = LEVEL
;         SHARE = NO
;
;      CHOICE = "INT15 Level"
;      LINK
;        INIT = IOPORT(1) LOC(2-0) 110
;        IRQ = 15
;         TRIGGER = LEVEL
;         SHARE = NO

;   SUBFUNCTION = "Interrupt Latch"
;      CHOICE = "Unlatched (Default)"
;        LINK
;        INIT = IOPORT(1) LOC(3) 0
;
;      CHOICE = "latched"
;        LINK
;        INIT = IOPORT(1) LOC(3) 1