; ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
; º  Adaptec AHA-1540B SCSI configuration file.     º
; º  ID: AHB1540                                    º
; º  Version: 1.00              Revision 1          º
; º  Date: January 21th, 1992   By: RVG/MB          º
; ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
;
BOARD
   ID = "AHB1540"
   NAME = "Adaptec AHA-1540 B SCSI Harddisk Controller"
   MFR = "Adaptec, Inc"
   CATEGORY = "MSD"
   SLOT = ISA16
   LENGTH = 330
   AMPERAGE = 2100
   READID = NO
   COMMENTS =
   "Adaptec AHA-1540 B SCSI Harddisk Controller configuration file.\n
    Version 1.00                         Date: September 11th, 1990"
   HELP = "When using the AHA1540 B Controller and an Isolan AT-Controller
      with NetWare286, you have to load the VAP 'AHA1540.VAP'. When using
      this card in combination with the Isolan AT-Controller in a NetWare386
      environment, you have to adjust the time between BUS_ON and BUS_OFF."

JUMPER(1) = 13
   NAME = "JUMPER BLOCK 5"
   JTYPE = PAIRED
   REVERSE = YES
   LABEL = LOC (1-13) "Sync. Neg." "Diagnostic" "Parity" "ID Sel. 0"
      "ID Sel. 1" "ID Sel. 2" "DMA Sel. 0" "DMA Sel. 1" "IRQ Sel. 0"
      "IRQ Sel. 1" "IRQ Sel. 2" "Transfer 0" "Transfer 1"
   FACTORY = LOC (1-13) 0000000101000

JUMPER(2) = 5
   NAME = "JUMPER BLOCK 6"
   JTYPE = PAIRED
   REVERSE = YES
   LABEL = LOC (1-5) "EnableBIOS" "SPARE 1" "SPARE 2" "SPARE 3" "Auto Sense"
   INITVAL = LOC (2-4) 000
   FACTORY = LOC (1 5) 10

JUMPER(3) = 8
   NAME = "JUMPER BLOCK 7"
   JTYPE = PAIRED
   REVERSE = YES
   VERTICAL = YES
   LABEL = LOC (1-8) "NA" "IO Sel. 0" "IO Sel. 1" "IO Sel. 2"
           "WS Bit 0" "WS Bit 1" "BIOS Sel.0" "BIOS Sel.1"
   INITVAL = LOC(1) 0
   FACTORY = LOC (2-8) 1000000

JUMPER(4) = 14
   NAME = "JUMPER BLOCK 9"
   JTYPE = PAIRED
   REVERSE = YES
   LABEL = LOC (1-14) " 1" " 2" " 3" " 4" " 5" " 6" " 7" " 8" " 9" " 10"
      " 11" " 12" " 13" " 14"
   FACTORY = LOC (1-14) 01000100001000

GROUP = "Resources"
   TYPE = "HDC"

FUNCTION = "DMA Channel"
   CHOICE = "Select"
      LINK
      DMA = 5 | 6 | 7 | 0
         SIZE = WORD
         TIMING = TYPEA
      INIT = JUMPER (1) LOC (7-8) 01 | 10 | 00 | 11
      INIT = JUMPER (4) LOC (1-4) 0100 | 0010 | 0001 | 1000
      INIT = JUMPER (4) LOC (5-8) 0100 | 0010 | 0001 | 1000
   COMMENTS = "The AHA 1540 B Controller acts as ISA BUS MASTER."

FUNCTION = "IRQ Level"
   CHOICE = "Select"
      FREE
      IRQ = 11 | 9 | 10 | 12 | 14 | 15
      INIT = JUMPER(1) LOC(9-11) 010 | 000 | 100 | 110 | 001 | 101
      INIT = JUMPER(4) LOC(9-14) 001000 | 100000 | 010000 |
                        000100 | 000010 | 000001
   COMMENTS = "The standard (ST506) disk-interface uses IRQ 14."

FUNCTION = "IO-Base"
   CHOICE = "Select"
      LINK
      PORT = 330h-332h | 334h-336h | 234h-236h |
          230h-232h | 134h-136h | 130h-132h
         SIZE = BYTE
      INIT = JUMPER(3) LOC(2-4) 100 | 000 | 010 | 110 | 001 | 101
   COMMENTS = "Booting is only possible with BIOS enabled and IO-Base
      installed at 330h."

FUNCTION = "BIOS Base Address"
   CHOICE = "Select"
      LINK
      MEMORY = 16K
         ADDRESS = 0DC000h | 0CC000h | 0D8000h | 0C8000h
         MEMTYPE = OTH
         WRITABLE = NO
      INIT = JUMPER(3) LOC(7-8) 00 | 10 | 01 | 11
      INIT = JUMPER(2) LOC(1) 1 | 1 | 1 | 1
      INIT = JUMPER(3) LOC(5-6) 00 | 00 | 00 | 00
   CHOICE = "Disabled"
      FREE
      INIT = JUMPER(2) LOC(1) 0
   HELP = "When using 2 AHA 1540 Controllers, make sure that only 1
      controller has the onboard BIOS enabled."

ENDGROUP

FUNCTION = "DMA Transfer Speed"
   CHOICE = "5.0 MB/s"
      FREE
      INIT = JUMPER(1) LOC(12-13) 00
   CHOICE = "5.7 MB/s"
      FREE
      INIT = JUMPER(1) LOC(12-13) 10
   CHOICE = "6.7 MB/s"
      FREE
      INIT = JUMPER(1) LOC(12-13) 01
   CHOICE = "8.0 MB/s"
      FREE
      INIT = JUMPER(1) LOC(12-13) 11

GROUP = "SCSI Options"
      
FUNCTION = "SCSI Address Sel."
   CHOICE = "ID 7"
      FREE
      INIT = JUMPER(1) LOC(4-6) 000
   CHOICE = "ID 6"
      FREE
      INIT = JUMPER(1) LOC(4-6) 100
   CHOICE = "ID 5"
      FREE
      INIT = JUMPER(1) LOC(4-6) 010
   CHOICE = "ID 4"
      FREE
      INIT = JUMPER(1) LOC(4-6) 110
   CHOICE = "ID 3"
      FREE
      INIT = JUMPER(1) LOC(4-6) 001
   CHOICE = "ID 2"
      FREE
      INIT = JUMPER(1) LOC(4-6) 101
   CHOICE = "ID 1"
      FREE
      INIT = JUMPER(1) LOC(4-6) 011
   CHOICE = "ID 0"
      FREE
      INIT = JUMPER(1) LOC(4-6) 111
   COMMENTS = "Every device on the SCSI-Bus must have an unique SCSI-ID, with
      ID 7 having the highest priority."

FUNCTION = "Auto Sence"
   CHOICE = "Enabled"
      FREE
      INIT = JUMPER(2) LOC(5) 0
   CHOICE = "Disabled"
      FREE
      INIT = JUMPER(2) LOC(5) 1
   COMMENTS = "Disabling this function could lead to unpredictable results"

FUNCTION = "Transfer Negotiation"
   CHOICE = "Disabled"
      FREE
      INIT = JUMPER(1) LOC(1) 0
   CHOICE = "Enabled"
      FREE
      INIT = JUMPER(1) LOC(1) 1
   COMMENTS = "When this jumper is installed, an other SCSI-device has to
      initiate Synchronous Transfer handshake."
     
FUNCTION = "SCSI Parity"
   CHOICE = "Enabled"
      FREE
      INIT = JUMPER(1) LOC(3) 0
   CHOICE = "Disabled"
      FREE
      INIT = JUMPER(1) LOC(3) 1
   COMMENTS = "SCSI Parity enhances data integrety."

FUNCTION = "SCSI Connector Type"
   CHOICE = "Internal SCSI Connector, J2"
   CHOICE = "External SCSI Connector, J4"
   COMMENTS = "Make sure the SCSI-Bus is terminated by the first and last
      device on the SCSI-Bus."

FUNCTION = "Terminator Power"
   CHOICE = "By AHA1540 B"
   CHOICE = "By other SCSI-device"
   COMMENTS = "If fuse F1 is installed, the AHA1540-B provides Terminator
      Power. It is also possible for another SCSI-device to provide
      Terminator Power by removing the fuse."

ENDGROUP