; ; Altos EISA Tester Board II ; BOARD ID = "ACS0611" NAME = "EISA Tool" MFR = "ACER/Altos Computer Systems" CATEGORY = "OTH" SLOT = EISA LENGTH = 330 AMPERAGE = 2870 SKIRT = NO READID = YES ; BUSMASTER = 99 ;Can be a busmaster but not required IOCHECK = INVALID DISABLE = UNSUPPORTED COMMENTS="This board contains 8K bytes of RAM and control logic allowing the board to run EISA cycles as a master or slave. The board can run as a 16 bit or 32 bit device in bursting or non-bursting mode and may contain an optional ROM." IOPORT(1) = 0z482h SIZE = DWORD INITVAL = 0000000xxxxxxxxxxxxxxxxx00xxx000 ;d24 = Enable RAM Access JUMPER(1) = 1 NAME = "E2 1 & 2" JTYPE = PAIRED VERTICAL = YES REVERSE = NO LABEL = LOC(1) "0e0000h" FACTORY = LOC(1) 0 COMMENTS = "This jumper sets the base address of the onboard ROM to 0e0000h or 0d0000h." HELP = "Jumper installed sets ROM address to 0e0000h. Jumper removed sets ROM address to 0d0000h." JUMPER(2) = 1 NAME = "E2 3 & 4" JTYPE = PAIRED VERTICAL = YES REVERSE = NO LABEL = LOC(1) "Disable" FACTORY = LOC(1) 0 COMMENTS = "This jumper disables the onboard ROM." HELP = "Installing the jumper disables the ROM, removing the jumper enables the ROM." JUMPER(3) = 1 NAME = "E1" JTYPE = PAIRED VERTICAL = YES REVERSE = NO LABEL = LOC(1) "NMI" INITVAL = LOC(1) 0 FACTORY = LOC(1) 0 COMMENTS = "The temporary installation of this jumper causes a hardware generated NMI (Non-Maskable Interrupt) to occur. This jumper is to be used for debug purposes by a qualified technician only." FUNCTION = "EISA Tool RAM" TYPE = "MEM,RAM" CHOICE = "Enabled" LINK MEMORY = 2000h ;8k size ADDRESS = 4000000h - 7FFFE000h step=10000h ; 64m to 2g in 64k steps WRITABLE = YES MEMTYPE = OTH CACHE = NO SHARE = NO INIT = IOPORT(1)LOC(23-8) 0000010000000000 - 0111111111111111 FREE INIT = IOPORT(1)LOC(24) 1 CHOICE = "Disabled" DISABLE = YES FREE INIT = IOPORT(1)LOC(24) 0 FUNCTION = "EISA Tool ROM" TYPE = "MEM,ROM" CHOICE = "Enabled" LINK MEMORY = 64k ADDRESS = 0d0000h | 0e0000h WRITABLE = NO MEMTYPE = OTH CACHE = YES SHARE = NO INIT = JUMPER(1)LOC(1) 0 | 1 FREE INIT = JUMPER(2)LOC(1) 0 CHOICE = "Disabled" DISABLE = YES FREE INIT = JUMPER(2)LOC(1) 1 FUNCTION = "EISA Tool Transfer IRQ" TYPE = "DMA,IRQ" CHOICE = "Enabled" LINK IRQ = 7 | 9 | 10 | 11 | 14 | 15 SHARE = "OTH" TRIGGER = LEVEL INIT = IOPORT(1)LOC(5-3) 010 | 011 | 100 | 101 | 110 | 111 CHOICE = "Disabled" DISABLE = YES FREE INIT = IOPORT(1)LOC(5-3) 000 ; ******************************************************************* ; Revision History: ;