;
; HPFP Configuration File V1.0
;

BOARD
	ID		= "ACS0501"
	NAME		= "Altos High-Performance File Processor"
	MFR		= "Altos"
	CATEGORY	= "MSD"
	SLOT		= EISA
	LENGTH		= 330
	AMPERAGE	= 6500
	SKIRT		= NO
	READID		= YES
	BUSMASTER	= 50
	IOCHECK		= INVALID
	DISABLE		= SUPPORTED
	COMMENTS	= "The HPFP is a single ported SCSI
			controller that may be turned into a dual ported
			SCSI controller with an optional daughter card."

;
; I/O Control Ports
;
IOPORT(1)		= 0zC8CH
	SIZE		= DWORD
	INITVAL		= 00000000000011xxxxxx000000001111b
	
IOPORT(2)		= 0z4D1H
	SIZE		= BYTE
        INITVAL         = xxxxxxxx

;
; Jumpers
;
JUMPER(1)		= 1
	NAME		= "JX1"
	JTYPE		= PAIRED
        VERTICAL        = NO
        REVERSE         = NO
	FACTORY		= LOC (1) 1
	COMMENTS	= "If this jumper is installed, the board will
			generate level triggered interrupts"

JUMPER(2)		= 1
	NAME		= "JA1"
	JTYPE		= PAIRED
	
VERTICAL        = NO
        REVERSE         = NO
	FACTORY		= LOC (1) 1
	COMMENTS	= "Installing this jumper supplies terminator
			power to the SCSI bus."
			
JUMPER(3)               = 11
        NAME            = "JAX1"
        JTYPE           = PAIRED
        VERTICAL        = NO
        REVERSE         = NO
        INITVAL         = LOC(1 2 3 4 5 6 7 8)11000000
        FACTORY         = LOC(1 2 3 4 5 6 7 8 9 10 11)11000000000
        COMMENTS        = "JAX1 Jumpers set the SCSI ID for channel 0 plus
                        whether or not the SCSI bus is reset on power up or
                        board reset and whether or not the 4810 extended
                        diagnostic is run on power up. With JAX1 pins 1-2
                        installed, SCSI bus reset at power on is not done and
                        with JAX1 pins 3-4 installed, extended diagnostic is
                        not performed."

JUMPER(4)               = 1
        NAME            = "JAX2"
        JTYPE           = PAIRED
        VERTICAL        = NO
        REVERSE         = NO
        INITVAL         = LOC(1) 1
        FACTORY         = LOC(1) 1
        COMMENTS        = "This jumper is used to isolate 36 MHZ OSC from
                        logic on the board. It is to be removed only for
                        manufacturing board test."

JUMPER(5)               = 1
        NAME            = "JA2"
        JTYPE           = PAIRED
        VERTICAL        = YES
        REVERSE         = NO
        INITVAL         = LOC(1) 1
        FACTORY         = LOC(1) 1
        COMMENTS        = "This jumper is used to isolate 24 MHZ processor
                        clock from logic on the board. It is to be removed
                        only for manufacturing board test."

JUMPER(6)               = 1
        NAME            = "JA4"
        JTYPE           = PAIRED
        VERTICAL        = YES
        REVERSE         = NO
        INITVAL         = LOC(1) 0
        FACTORY         = LOC(1) 0
        COMMENTS        = "The setting on this jumper should not be changed."

JUMPER(7)               = 1
        NAME            = "JA5"
        JTYPE           = PAIRED
        VERTICAL        = YES
        REVERSE         = NO
        INITVAL         = LOC(1) 1
        FACTORY         = LOC(1) 1
        COMMENTS        = "This jumper is used to isolate 24 MHZ SCSI clock
                        from Logic on the board. It is to be removed only
                        for manufacturing board test." 

JUMPER(8)               = 2
        NAME            = "JA6"
        JTYPE           = INLINE
        VERTICAL        = NO
        REVERSE         = NO
        INITVAL         = LOC(1^2 2^3) 01
        FACTORY         = LOC(1^2 2^3) 01
        COMMENTS        = "256k EPROMS are enabled by installing the jumper
						on 2^3. For 512k EPROMS the jumper must be installed
					    on 1^2."

JUMPER(9)               = 1
        NAME            = "JA1 ON DAUGHTER CARD"
        JTYPE           = PAIRED
        VERTICAL        = YES
        REVERSE         = YES
        FACTORY         = LOC(1) 1
        COMMENTS        = "JA1-3 set the SCSI ID for channel 1"

JUMPER(10)              = 1
        NAME            = "JA2 ON DAUGHTER CARD"
        JTYPE           = PAIRED
        VERTICAL        = YES
        REVERSE         = YES
        FACTORY         = LOC(1) 1
        COMMENTS        = "JA1-3 set the SCSI ID for channel 1"

JUMPER(11)              = 1
        NAME            = "JA3 ON DAUGHTER CARD"
        JTYPE           = PAIRED
        VERTICAL        = YES
        REVERSE         = YES
        FACTORY         = LOC(1) 1
        COMMENTS        = "JA1-3 set the SCSI ID for channel 1"

JUMPER(12)              = 1
        NAME            = "JA4 ON DAUGHTER CARD"
        JTYPE           = PAIRED
        VERTICAL        = YES
        REVERSE         = YES
        FACTORY         = LOC(1) 1
	COMMENTS	= "Installing this jumper supplies terminator
			power to the SCSI bus."



FUNCTION 		= "HPFP SCSI Controller"
TYPE = "MSD,HPFP"

	SUBFUNCTION = "RESOURCE CONFIGURATION"
        COMMENTS = "It is through this dual ported memory that all commands
                    and status are passed between the HPFP and the host 
                    system."
	    CHOICE = "CONFIGURE MEMORY, PORTS, INTERRUPTS"
		LINK
		    MEMORY = 4k
			ADDRESS = 0C8000h-0E8000h STEP = 4K
			MEMTYPE = OTH
			WRITABLE = YES
			SIZE = DWORD
			CACHE = NO
		    INIT = IOPORT(1) LOC(17-12) 001000-101000
		FREE
		    PORT = 0z4D1h
			SIZE = BYTE
		    INIT = IOPORT(2) 00001000
		SUBCHOICE
		FREE
		    IRQ = 14|15|7|11|5|10|12|3|4|6
			SHARE = "msd"
			TRIGGER = LEVEL
			INIT = JUMPER(1) LOC(1) 1
		SUBCHOICE
		FREE
		    IRQ = 14|15|7|11|5|10|12|3|4|6
			SHARE = NO
			TRIGGER = EDGE
			INIT = JUMPER(1) LOC(1) 0
		
	SUBFUNCTION = "HPFP SCSI CHANNEL 0 ID"
        COMMENTS = "This is the primary SCSI channel on the HPFP."
        HELP = "Jumper 2 should be installed in order to provide termination
                power to the SCSI bus."
	    CHOICE = "7"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 000

	    CHOICE = "6"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 100

	    CHOICE = "5"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 010

	    CHOICE = "4"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 110

	    CHOICE = "3"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 001

	    CHOICE = "2"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 101

	    CHOICE = "1"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 011

	    CHOICE = "0"
                FREE
                INIT = JUMPER(3) LOC(9 10 11) 111


	SUBFUNCTION = "HPFP SCSI CHANNEL 1 ID"
        COMMENTS = "This channel is only available if the daughter card is
                    installed."
	    CHOICE = "7"
                FREE
                INIT = JUMPER(9) LOC(1) 1
                INIT = JUMPER(10) LOC(1) 1
                INIT = JUMPER(11) LOC(1) 1

	    CHOICE = "6"
                FREE
                INIT = JUMPER(9) LOC(1) 0
                INIT = JUMPER(10) LOC(1) 1
                INIT = JUMPER(11) LOC(1) 1

	    CHOICE = "5"
                FREE
                INIT = JUMPER(9) LOC(1) 1
                INIT = JUMPER(10) LOC(1) 0
                INIT = JUMPER(11) LOC(1) 1

	    CHOICE = "4"
                FREE
                INIT = JUMPER(9) LOC(1) 0
                INIT = JUMPER(10) LOC(1) 0
                INIT = JUMPER(11) LOC(1) 1

	    CHOICE = "3"
                FREE
                INIT = JUMPER(9) LOC(1) 1
                INIT = JUMPER(10) LOC(1) 1
                INIT = JUMPER(11) LOC(1) 0

	    CHOICE = "2"
                FREE
                INIT = JUMPER(9) LOC(1) 0
                INIT = JUMPER(10) LOC(1) 1
                INIT = JUMPER(11) LOC(1) 0

	    CHOICE = "1"
                FREE
                INIT = JUMPER(9) LOC(1) 1
                INIT = JUMPER(10) LOC(1) 0
                INIT = JUMPER(11) LOC(1) 0

	    CHOICE = "0"
                FREE
                INIT = JUMPER(9) LOC(1) 0
                INIT = JUMPER(10) LOC(1) 0
                INIT = JUMPER(11) LOC(1) 0